How to Calculate Velocity of a Rocket Sled After Passing Over a Rough Patch

  • Thread starter Thread starter xavior6
  • Start date Start date
  • Tags Tags
    Grade 11 Physics
AI Thread Summary
To calculate the velocity of a rocket sled after passing over a rough patch, the sled's initial velocity is 24 m/s with a friction force of 6000N acting against it. The sled's mass is determined to be approximately 2038.7 kg. The net force is solely due to friction, leading to an acceleration of -2.94 m/s². Using the formula Vf² = Vi² + 2ad, the calculated exit velocity is found to be 22.6 m/s, but there is a discrepancy as the expected answer is 23.7 m/s. The discussion emphasizes the importance of checking arithmetic and significant figures in calculations.
xavior6
Messages
9
Reaction score
0

Homework Statement


A Rocket Sled weighing 20000N is gliding at 24 m/s (North) on ice where friction is negligible. Suddenly it passes over a rough patch 22m long, which creates a friction force of 6000N (south). With what velocity does the sled leave the rough patch?


Homework Equations


Vi=Vf+ad
Vf(squared)=Vi(squared)+2ad
Fnet=Ff+Fa
Fnet= Ma


The Attempt at a Solution



I figured that the Vi of the sled when it hits the patch is 24 m/s since there is no acceleration. When it hits the patch, there are two forces on the object; one with -6000N and the other which is the original force applied. The sum of these constitutes the net force. The net force is also equal to the Mass of the object x Acceleration. The mass is 20000/9.81 which equals roughly 2038.7KG.

If I find acceleration, I would easily find the Vf of the object leaving the rough patch. The problem is, I have no idea how to find the forward force of the rocket sled, so I am left with 2 variables in 1 equation and I am stuck.

Can someone please tell me the way to solve this? Thank you.
 
Physics news on Phys.org
xavior6 said:
I figured that the Vi of the sled when it hits the patch is 24 m/s since there is no acceleration. When it hits the patch, there are two forces on the object; one with -6000N and the other which is the original force applied.
There's only one horizontal force acting on the sled--the friction. There's no "original force" needed to keep the sled moving as it glides over the ice.


The sum of these constitutes the net force. The net force is also equal to the Mass of the object x Acceleration. The mass is 20000/9.81 which equals roughly 2038.7KG.

If I find acceleration, I would easily find the Vf of the object leaving the rough patch. The problem is, I have no idea how to find the forward force of the rocket sled, so I am left with 2 variables in 1 equation and I am stuck.
There is no forward force, just friction. Perhaps you are thinking of the force that was needed to get the sled moving at 24 m/s? Once it got moving, no force is needed to keep going. (Newton's 1st law.)
 
Hmm what you say makes complete sense. But i still do not reach the correct answer. Using your advice, the modified solution method would be:

Fnet= -6000N
Fnet= 2038.7Kg(a)
a= -2.94.

Solving this using the Vf(squared)=Vi(squared)+2(a)(d) formula, Vf= 22.6 m/s
The answer is 23.7 m/s, so I am off by a factor of 1.1. Can you point me to the right direction as to what may have caused this deviation? I'm quite sure it can't be rounding errors.
 
Your method is perfectly correct. (I'd say that your answer is a bit too high--recheck your arithmetic!) No reason to think that 23.7 m/s is correct. (Also, realistically speaking, only 2 digits--at most--are significant.)
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Collision of a bullet on a rod-string system: query'
In this question, I have a question. I am NOT trying to solve it, but it is just a conceptual question. Consider the point on the rod, which connects the string and the rod. My question: just before and after the collision, is ANGULAR momentum CONSERVED about this point? Lets call the point which connects the string and rod as P. Why am I asking this? : it is clear from the scenario that the point of concern, which connects the string and the rod, moves in a circular path due to the string...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top