How to Determine Resistive Force and Engine Power at Different Speeds?

AI Thread Summary
The discussion focuses on calculating the resistive force and engine power of an automobile at different speeds. The resistive force at 80 km/h is determined to be approximately 1510 N using power and velocity conversions. For the speed of 60 km/h, participants are tasked with finding the corresponding engine power, noting that the resistive force will be less than 1510 N due to its proportional relationship with velocity. There is confusion among participants regarding the equations needed to solve these problems, prompting suggestions to refer back to textbooks for relevant formulas. The conversation emphasizes understanding the relationship between force, velocity, and power in automotive physics.
sanisydap
Messages
3
Reaction score
0
1. The engine of an automobile requires 45hp to maintain a constant speed of 80 km/h

a. What is the resistive force against the automobile?
The answer given here is 1510.80N but don't know how they get it.

b. If the resistive force is proportional to the velocity, what must the engine power be to drive at constant speed of 60km/h?


2. I have no idea

3. at letter a. i tried to convert 45hp to 33556.49J/s and converted also 80km/h to 22.22 m/s, after that I divided 33556.49J/s to 22.22 m/s and got an answer 1510.19 N. The letter b. I have no idea
 
Last edited:
Physics news on Phys.org
Welcome to Physics Forums :smile:

I see you figured out (a) based on looking at units. There is also an equation that relates power, force and velocity that should be in your textbook.

For (b), here are 2 facts known to you:

1. Force is proportional to velocity.
2. When the velocity is 80 km/hr, the force is 1510 N.

Use those 2 facts can be used to determine the relationship between force and velocity for this automobile.
 
so i will be finding what? I think its power.. i am confused to the equation i will be using.. i kinda do trial and error xD
 
Last edited:
sanisydap said:
so i will be finding what? I think its power..
Re-read what question (a) is asking. (Hint: not power)
i am confused to the equation i will be using.. i kinda do trial and error xD
Try looking in your textbook and class notes and see what equation would relate power, force and velocity.
 
I think i got it now..so question b . is asking about the engine power at 60km/h .. then i got a force of 1510.19N, convert 60 km/h to 16.67m/s and multiplied them, then the answer would be 25,174.87 J/s.. i think hehehe
 
No, the force is 1510 N when the speed is 80 km/h, but now (in question b) it is 60 km/h. So the force will be less than 1510 N.

Redbelly98 said:
For (b), here are 2 facts known to you:

1. Force is proportional to velocity.
2. When the velocity is 80 km/hr, the force is 1510 N.
Can you set up an equation expressing the proportional relation between force and velocity?
 
Thread 'Voltmeter readings for this circuit with switches'
TL;DR Summary: I would like to know the voltmeter readings on the two resistors separately in the picture in the following cases , When one of the keys is closed When both of them are opened (Knowing that the battery has negligible internal resistance) My thoughts for the first case , one of them must be 12 volt while the other is 0 The second case we'll I think both voltmeter readings should be 12 volt since they are both parallel to the battery and they involve the key within what the...
Thread 'Correct statement about a reservoir with an outlet pipe'
The answer to this question is statements (ii) and (iv) are correct. (i) This is FALSE because the speed of water in the tap is greater than speed at the water surface (ii) I don't even understand this statement. What does the "seal" part have to do with water flowing out? Won't the water still flow out through the tap until the tank is empty whether the reservoir is sealed or not? (iii) In my opinion, this statement would be correct. Increasing the gravitational potential energy of the...
Back
Top