Imposing high frequency on AC mains

AI Thread Summary
The discussion revolves around a project to superimpose a high-frequency component onto a 240V AC mains supply at 60Hz, similar to the ripples produced by petrol generators. The initial inquiry seeks guidance on practical implementation, including necessary components like signal generators and frequency mixers. Participants highlight the importance of adhering to regulations regarding conducted emissions in different countries, particularly in the US and EU. A reference to existing technology, such as the X10 remote control system, illustrates a practical application of high-frequency signals over AC mains. The user from the UK requests specific component recommendations and a block diagram for practical implementation.
shaik.as22
Messages
3
Reaction score
0
Hi All,
Currently Iam working on a project where I have to superimpose High frequency component on AC mains 240V 60HZ. ( Its imposing Ripples in mains voltage... as happens when voltage is generated from a Petrol generator). Need some help how would i do this ?

Thanks in advance.
Shakey...
 
Engineering news on Phys.org
By the formula, it is two voltages in series, for example,

50V + 5V * sin (2*pi*60*time)

This will be a DC 50V plus an AC ripple with 60HZ 5V peak.

50V * sin (2*pi*60*time) + 5V * sin (2 *pi* 600000*time)

This will be a 50V peak 60HZ AC plus an AC ripple with 5V peak at 600kHz.



shaik.as22 said:
Hi All,
Currently Iam working on a project where I have to superimpose High frequency component on AC mains 240V 60HZ. ( Its imposing Ripples in mains voltage... as happens when voltage is generated from a Petrol generator). Need some help how would i do this ?

Thanks in advance.
Shakey...
 
Look at the X10 remote control system that has been around (in the U.S.) for 30 years. It uses a high frequency (100's of kilohertz) to remotely control appliances over the AC mains. I was even able to remotely turn on and off a lamp in my neighbor's house using a plug-in lamp control unit. There are now other brands on the market. See http://www.pcmag.com/article2/0,2817,1675067,00.asp
 
shaik.as22 said:
Hi All,
Currently Iam working on a project where I have to superimpose High frequency component on AC mains 240V 60HZ. ( Its imposing Ripples in mains voltage... as happens when voltage is generated from a Petrol generator). Need some help how would i do this ?

Thanks in advance.
Shakey...

For most countries, there are regulations for what frequencies and what amplitudes you can couple into the powerlines. What country are you in? In the US and in the EU, there are strict regulations governing the "conducted emissions" on powerlines.
 
Thanks for your replies Fuxue and Berkeman...
Fuxue, I understand theroy behind it but i want to implement it practically. So What are the components i should be looking for, like signal generator/frequency mixer... etc..

Berkeman I am from United Kingdom

please suggest me what are the components i will be requiring. if possible block diagram of connection made..
 
Please see the attachment... how can I achieve pratically what are the components/devices required
 

Attachments

  • 02109.png
    02109.png
    3.2 KB · Views: 597

Thread 'What happens if shielded cable has a short to the shield?'

While I was rolling out a shielded cable, a though came to my mind - what happens to the current flow in the cable if there came a short between the wire and the shield in both ends of the cable? For simplicity, lets assume a 1-wire copper wire wrapped in an aluminum shield. The wire and the shield has the same cross section area. There are insulating material between them, and in both ends there is a short between them. My first thought, the total resistance of the cable would be reduced...
View full post »

Thread 'Underwater piezoelectric sensor array receive sensitivity'

Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
View full post »

Thread 'Question about bonding ground and neutral'

I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...
View full post »

Similar threads

Choosing a pulse capacitor, ESR vs reactance at frequency
Replies
5
Views
2K
Is There Still a Market for Mechanical High Power DC/AC Generators?
Replies
7
Views
2K
How Do You Handle KVL Limitations in High-Frequency AC Circuits?
Replies
4
Views
2K
Exploring LRC AC Series Circuits
Replies
25
Views
2K
Reducing AC inrush current in this setup
Replies
15
Views
3K
How Does Resonance Frequency Affect MEMS Accelerometer Performance?
Replies
1
Views
2K
Help with LTSPICE on a high frequency circuit
Replies
4
Views
3K
How can I apply a variable phase shift to an AC signal generated by a VFD?
Replies
9
Views
2K
Thoughts for a low-power 60Hz 120Vrms signal generator please
Replies
47
Views
5K
High Pass Filter Working Principle
Replies
15
Views
2K

Hot Threads

Recent Insights

Back
Top