Is There a Sensor to Detect Current Change and Turn on a Relay?

  • Thread starter Thread starter gyrgi
  • Start date Start date
  • Tags Tags
    Relay Turning
AI Thread Summary
The discussion centers on finding a sensor to detect current changes that can reactivate a relay connected to a wall device. A non-invasive current sensor is considered, but there are concerns about whether it will detect significant current changes when the device is powered on. Participants emphasize the need for more detailed information, including circuit diagrams and the specific features desired, to provide accurate advice. There is also a suggestion to consider simpler alternatives, such as using a switch or basic sensor. Overall, clarity and detail in the inquiry are crucial for effective assistance.
gyrgi
Messages
3
Reaction score
0
I'm trying to figure out a way to turn a relay back on with a sensor. This relay is attached to a device that is plugged into a wall. I was thinking of using a non-invasice current sensor but I don't know if there will be a significant current change, if any, once I turn the device on, if the relay is still turned off.

Is there a sensor to check the change in capacitance of the wire that is turned on?
 
Engineering news on Phys.org
gyrgi said:
I'm trying to figure out a way to turn a relay back on with a sensor. This relay is attached to a device that is plugged into a wall. I was thinking of using a non-invasice current sensor but I don't know if there will be a significant current change, if any, once I turn the device on, if the relay is still turned off.

Is there a sensor to check the change in capacitance of the wire that is turned on?

You kind of already asked this question here: https://www.physicsforums.com/threads/how-to-tell-a-wire-is-plugged-in.817417/

Did the replies in that thread not help you?
 
They are helpful on how to measure current without using current. But now I'm curious on if there is a sensor to turn a relay back on. I don't believe these methods suggested would work besides the "quantum oscillator " which I do not fully understand.

I was worried if I responded to that thread that it wouldn't be viewed.
 
gyrgi said:
Is there a sensor to check the change in capacitance of the wire that is turned on?
Yes, there are sensors but we need more information to answer your question.
The world is more complex than you realize. If you ask the right question you will get the right answer.
We require feedback from you to identify what your question actually means.
Can you produce a circuit diagram of what you have and describe the feature what you want to change or add.
 
You need to provide at least a block diagram that let's us see visually what functionality you are trying to achieve. What's this relay hooked to? Where does it get power? Why did it turn off?

Why can't you just hook up a switch or sensor to turn it back on.

I'm sure your actual application and issues are in your questions somewhere, but I can't really figure it out.

Details details details. We can't read minds.
 

Thread 'Underwater piezoelectric sensor array receive sensitivity'

Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
View full post »

Thread 'Following up on the recent thread about Earth Resistance measurements'

I have recently moved into a new (rather ancient) house and had a few trips of my Residual Current breaker. I dug out my old Socket tester which tell me the three pins are correct. But then the Red warning light tells me my socket(s) fail the loop test. I never had this before but my last house had an overhead supply with no Earth from the company. The tester said "get this checked" and the man said the (high but not ridiculous) earth resistance was acceptable. I stuck a new copper earth...
View full post »

Thread 'Question about bonding ground and neutral'

I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...
View full post »

Similar threads

Multiple signals controlling relay
Replies
7
Views
241
How can I reroute multiple signals from a 4 pin connector using a relay switch?
Replies
37
Views
6K
Samsung double door fridge overload relay changed 3 times in 2 weeks
Replies
12
Views
4K
Switching between parallel and series connections (solar)
Replies
31
Views
4K
Mosfet SSR, flyback shunt/crowbar safety circuit
Replies
1
Views
2K
Novice question about Relays, Capacitors, and Diodes
Replies
5
Views
5K
Alternative to Relay for Accurate Time Measurement Experiments
Replies
17
Views
3K
Can a Square Wave Tachometer Drive be Powered by a Sine Waveform?
Replies
16
Views
3K
Generator tripping on ground fault during load test
Replies
38
Views
7K
Can I use a relay to wire DC lights to a speaker?
Replies
14
Views
4K

Hot Threads

Recent Insights

Back
Top