Marx Generator Capacitance and Charge Storing Question

AI Thread Summary
A Marx generator functions by cascading capacitor discharges to achieve a final voltage that is a multiple of the initial voltage. The final capacitors, typically represented by a spark gap, act as a switch rather than storage devices, allowing the discharge to occur through a load. However, it is possible to modify the setup to store charge instead of discharging it, provided that adequate insulation and switching mechanisms are in place. The discussion also highlights the need for reliable resources, as users seek recommendations for books on Marx generators. Overall, the Marx generator can be adapted for charge storage with the right modifications.
JAlexander
Messages
2
Reaction score
0
Hello,

I have had a question on my mind that a generic google search has so far been unable to answer for me. I know that marx generators multiple voltage by cascading capacitor discharges so that you get a final voltage of n x Vinit - where n is number of capacitors and Vinit is your initial voltage.

In all videos and discussions I have seen, that final voltage gets discharged across the final capacitors - implying that just as the initial capacitors discharged, the final capacitors must also discharge in like manner.

My question is, if you did not want a final discharge, but instead wanted to store charge, is a marx generator capable of doing this? Or must the final capacitors discharge after cascading through the initial capacitors?

In other words, If I have two parallel plates rather than the little balls that you see for the final capacitors, and my final voltage at the end of n x Vint equals 20KV, can those parallel plates store the charge or no?
 
Engineering news on Phys.org
I think you mistake the purpose of the pairs of spheres. These are not capacitors, but a switch. The generator charges the capacitors in parallel, then these are connected in series across the load via the pair of balls. These balls form a spark gap. One if them might be attached to a swing arm or some other device, used to enable an arc to form between them. This arc then discharges the series connected capacitors through the load. The nonlinear properties of the arc help to shape the waveform if the discharge.
The spark gap switch is used because a regular switch would be damaged by the high violtages and currents involved in the discharge.
 
JAlexander said:
My question is, if you did not want a final discharge, but instead wanted to store charge, is a marx generator capable of doing this?

Yes it is (if you have adequate cap-to-cap switches and insulation level everywhere)
 
Thanks for the info, zoki. That is what I was looking for.

Can anyone recommend a good book on the topic of marx generators? Google searches aren't really cutting it.

-Thanks
 
While I was rolling out a shielded cable, a though came to my mind - what happens to the current flow in the cable if there came a short between the wire and the shield in both ends of the cable? For simplicity, lets assume a 1-wire copper wire wrapped in an aluminum shield. The wire and the shield has the same cross section area. There are insulating material between them, and in both ends there is a short between them. My first thought, the total resistance of the cable would be reduced...
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...

Similar threads

Replies
5
Views
2K
Replies
14
Views
6K
Replies
1
Views
3K
Replies
3
Views
2K
Replies
5
Views
2K
Back
Top