Maximising water flow into an intake on a race boat

AI Thread Summary
To optimize water flow into a racing jet boat intake, understanding the 'spoon effect' is crucial, as it involves water running along the hull and into the intake. The relationship between intake pressure and speed is significant, with higher pressure leading to increased speed. Factors such as the radius of the intake and the boat's weight, particularly for tunnel hulls, influence performance. The optimal radius may vary with speeds of 80, 100, and 110 mph. Detailed measurements and calculations are essential for maximizing efficiency and speed in racing conditions.
NZJet
Messages
2
Reaction score
0
I've looked at lot of information on the net and have picked up a few things.

My query is how to work out the optimum radius and measurements for the lead into an intake on a racing jet boat?

We cruedly term it the 'spoon effect' where the water runs along the bottom of the boat and up into the intake. The more the intake pressure the faster you go!

From what i can tell this is the form drag effect (correct me if wrong).

I imagine the radius (distance) will change with the speed relative to the water as well. The weight of the baot will also have an effect. These are tunnel hulls so the weight on the water is minimal.

I'm assuming speed will also be important? Assume 80, 100 and 110 mph

Any feedback appreciated. Happy to answer any questions on measurements etc... Help this petrolhead please!
 
Engineering news on Phys.org
too hard?
 

Thread 'Bubble formation in 4 mm gap vessel'

How did you find PF?: Via Google search Hi, I have a vessel I 3D printed to investigate single bubble rise. The vessel has a 4 mm gap separated by acrylic panels. This is essentially my viewing chamber where I can record the bubble motion. The vessel is open to atmosphere. The bubble generation mechanism is composed of a syringe pump and glass capillary tube (Internal Diameter of 0.45 mm). I connect a 1/4” air line hose from the syringe to the capillary The bubble is formed at the tip...
View full post »

Thread 'HP Required to move a robot 10meters at 1.5m/sec'

I need some assistance with calculating hp requirements for moving a load. - The 4000lb load is resting on ball bearing rails so friction is effectively zero and will be covered by my added power contingencies. Load: 4000lbs Distance to travel: 10 meters. Time to Travel: 7.5 seconds Need to accelerate the load from a stop to a nominal speed then decelerate coming to a stop. My power delivery method will be a gearmotor driving a gear rack. - I suspect the pinion gear to be about 3-4in in...
View full post »
Thread 'Calculate minimum RPM to self-balance a CMG on two legs'

Thread 'Calculate minimum RPM to self-balance a CMG on two legs'

Here is a photo of a rough drawing of my apparatus that I have built many times and works. I would like to have a formula to give me the RPM necessary for the gyroscope to balance itself on the two legs (screws). I asked Claude to give me a formula and it gave me the following: Let me calculate the required RPM foreffective stabilization. I'll use the principles of gyroscopicprecession and the moment of inertia. First, let's calculate the keyparameters: 1. Moment of inertia of...
View full post »

Similar threads

Personal Jet Boat Water Craft Thrust Question
Replies
8
Views
2K
Force of pressurized water exiting a hose or pipe?
Replies
20
Views
10K
What is the needed flow rate of the impeller with this info?
Replies
8
Views
2K
Can Wake Riding Slow Down a Lead Boat?
Replies
11
Views
6K
Hydrodynamic forces on a foil, Reynolds number, viscosity
Replies
17
Views
5K
Surface roughness in 2D sinusoidal corrugation
Replies
1
Views
4K
Water psi effect on boat transducer
Replies
2
Views
3K
How do different hull treatments affect water flow and boat speed?
Replies
12
Views
5K
Atmospheric humidity for water production.
Replies
3
Views
3K
What is the maximum speed of water flow in the intake pipe?
Replies
5
Views
2K

Hot Threads

Recent Insights

Back
Top