Mechanical Energy Lost In A One-dimensional Collision

AI Thread Summary
In a one-dimensional collision, a 1200-kg car traveling at 25 m/s collides with a 9000-kg truck moving at 20 m/s, resulting in the car's post-collision speed of 18 m/s. The truck's velocity after the collision is calculated to be approximately 20.9 m/s. The kinetic energy loss during the collision is calculated to be around -14,955 Joules, but the textbook answer is 8.74 kJ, leading to confusion over the discrepancy. The loss in mechanical energy is attributed to factors such as heat, physical deformation of the vehicles, and frictional dissipation. The discussion emphasizes the importance of careful calculation and consideration of energy transformation during collisions.
NoPhysicsGenius
Messages
58
Reaction score
0

Homework Statement




A 1200-kg car traveling initially with a speed of 25 m/s in an easterly direction crashes into the rear end of a 9000-kg truck moving in the same direction at 20 m/s. The velocity of the car right after the collision is 18 m/s to the east. (a) What is the velocity of the truck right after the collision? (b) How much mechanical energy is lost in the collision? How do you account for this loss in energy?


Homework Equations




m_1v_{1i} + m_2v_{2i} = m_1v_{1f} + m_2v_{2f}
K = \frac{1}{2}mv^2


The Attempt at a Solution




I was able to solve part (a) as follows ...

m_1v_{1i} + m_2v_{2i} = m_1v_{1f} + m_2v_{2f}
\Rightarrow v_{2f} = \frac{m_1v_{1i} + m_2v_{2i} - m_1v_{1f}}{m_2}
\Rightarrow v_{2f} = \frac{(1200 kg)(25 m/s) + (9000 kg)(20 m/s) - (1200 kg)(18 m/s)}{9000 kg} = 20.9 m/s east


For part (b), however, I didn't get very far ...

I know the energy loss is due to heat (thermal energy), but I could only calculate the loss in kinetic energy, not mechanical energy:

K_f - K_i = \frac{1}{2}m_1{v_{1f}}^2 + \frac{1}{2}m_2{v_{2f}}^2 - \frac{1}{2}m_1{v_{1i}}^2 - \frac{1}{2}m_2{v_{2i}}^2
\Rightarrow K_f - K_i = \frac{1}{2}(1200 kg)(18 m/s)^2 + \frac{1}{2}(9000 kg)(20.9 m/s)^2 - \frac{1}{2}(1200 kg)(25 m/s)^2 - \frac{1}{2}(9000 kg)(20 m/s)^2 = -14,955 Joules = -15.0 kJ

The problem is that the answer in the back of the book is 8.74 kJ.
 
Physics news on Phys.org
NoPhysicsGenius said:
I know the energy loss is due to heat (thermal energy), but I could only calculate the loss in kinetic energy, not mechanical energy:

K_f - K_i = \frac{1}{2}m_1{v_{1f}}^2 + \frac{1}{2}m_2{v_{2f}}^2 - \frac{1}{2}m_1{v_{1i}}^2 - \frac{1}{2}m_2{v_{2i}}^2
\Rightarrow K_f - K_i = \frac{1}{2}(1200 kg)(18 m/s)^2 + \frac{1}{2}(9000 kg)(20.9 m/s)^2 - \frac{1}{2}(1200 kg)(25 m/s)^2 - \frac{1}{2}(9000 kg)(20 m/s)^2 = -14,955 Joules = -15.0 kJ

The problem is that the answer in the back of the book is 8.74 kJ.

Check your calculation again: working with your numbers, I don't quite get the book's result, but it's close (-9310 J). (Be careful about how much you round-off by early in the calculation. I may not be getting the book's answer because I used 20.93 m/sec for the truck's later speed, rather than 20.9.)

As for where the energy went, the term "internal energy" is a catch-all for lots of processes. Some of the energy could well go into heating, but some could also go into "physical deformation" of the bodies of the car and truck (crash damage), into frictional dissipation with the road surface because the rolling of tires briefly became sliding, and (a rather tiny bit) into sound (acoustical) energy.
 
Last edited:
I can't see anything wrong with your calculation. Mechanical energy is kinetic energy that isn't thermal energy.
 
i get -8680 no rounding
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...

Similar threads

Back
Top