How Many Bolts Are Needed for PVC Flanges on a Filter Column?

  • Thread starter Thread starter Bashir2008
  • Start date Start date
  • Tags Tags
    Bolts
AI Thread Summary
For a filter column with a 315mm outside diameter and 3m length, standard PVC flanges are recommended due to the low pressure involved. The number and size of bolts depend on the specific design and load requirements, but using standard bolts for PVC flanges is advisable. It's important to include gaskets for a proper seal, especially with wire mesh between flanges. If custom design is pursued, understanding the expected loads and pressures is crucial for accurate analysis. Proper selection of materials and components will ensure the integrity of the filter column assembly.
Bashir2008
Messages
7
Reaction score
0
Hello everyone.

I really in dire need of your help as i am not a mechanical engineer, so at this stage i am busy finding out the right design of PVC flanges for a filter column.
But the thing is
How to choose the right bolts ? i mean how many bolts should i have for my flanges and what size of bolts..

What i can tell u is my filter column is 315mm outside diameter and 3 m length and the filter is of 3 sections and i need to connect these sections by grey PVC flanges..and i will put a wire mesh between the flanges

by the way, the filter column is a clear PVC

So please how can i start with ?

Try to help me

Best regards
 
Engineering news on Phys.org
Since it's PVC, it has to be relatively low pressure. Just use standard PVC flanges and the respective bolts and gaskets. That would be the easiest. If you want to design your own, you need to know the expected loads and pressures before starting an analysis.
 
Thread 'Turbocharging carbureted petrol 2 stroke engines'

Thread 'Turbocharging carbureted petrol 2 stroke engines'

Hi everyone, online I ve seen some images about 2 stroke carbureted turbo (motorcycle derivation engine). Now.. In the past in this forum some members spoke about turbocharging 2 stroke but not in sufficient detail. The intake and the exhaust are open at the same time and there are no valves like a 4 stroke. But if you search online you can find carbureted 2stroke turbo sled or the Am6 turbo. The question is: Is really possible turbocharge a 2 stroke carburated(NOT EFI)petrol engine and...
View full post »

Thread 'HP Required to move a robot 10meters at 1.5m/sec'

I need some assistance with calculating hp requirements for moving a load. - The 4000lb load is resting on ball bearing rails so friction is effectively zero and will be covered by my added power contingencies. Load: 4000lbs Distance to travel: 10 meters. Time to Travel: 7.5 seconds Need to accelerate the load from a stop to a nominal speed then decelerate coming to a stop. My power delivery method will be a gearmotor driving a gear rack. - I suspect the pinion gear to be about 3-4in in...
View full post »

Similar threads

Determine how many bolts are needed to secure a block of steel
Replies
1
Views
2K
Can FEA Be Avoided in Analyzing Double Pipe Clamp Structures?
Replies
5
Views
2K
How to Design Bolts and Through Rods for Mounting Brackets on Columns?
Replies
1
Views
3K
Can a Bolt Withstand Double Shear Stress in Multi-Bar Configurations?
Replies
9
Views
4K
Brake caliper bracket mount - single shear bolt question
Replies
17
Views
16K
Calculating total stress in bolts that holds an actuator?
Replies
5
Views
11K
Tension, shear and torque acting on a bolt and cantilever.
Replies
2
Views
13K
How can I effectively brainstorm for FMEA analysis on bolts in a manufactory?
Replies
11
Views
8K
Recommendation Needed for a Spectrum Analyzer
Replies
46
Views
3K
How Do I Determine the Minimum Thickness for a PVC Board?
Replies
1
Views
3K

Hot Threads

Recent Insights

Back
Top