Pulsed laser diode driver - how it works?

AI Thread Summary
The discussion revolves around the operation of a pulsed laser diode driver and a potential error in its data sheet. The user explains how the circuit charges a capacitor and discharges it through the output diode to produce a laser pulse. They express confusion regarding the direction of electron flow depicted in the data sheet, questioning whether it is accurately represented. Another participant confirms the user's interpretation, highlighting a common concern about trusting data sheet information. The driver in question is identified as part of a commercial product from Directed Energy.
McKendrigo
Messages
25
Reaction score
0
Hi everyone,

I've been looking at the data sheet for a pulsed laser diode driver that I've been using, and I've managed to convince myself that there's a mistake. I was hoping that if I post my explanation of how the circuit shown in the data sheet works, that you guys can either confirm that the data sheet is wrong, or (embarrassingly) tell me that I'm wrong :redface:

I've attached the circuit as shown in the data sheet. My explanation is as follows (which is more or less what the data sheet says):

When S1 is open, the capacitor Cpfn charges by the high voltage input, HV_IN, through the clamping diodes D1 and D2. The output laser diode is reverse biased in this case, so no current flows through it. When S1 is closed, D1, D2 and the output diode are effectively connected in parallel with the capacitor Cpfn. Because D1 and D2 are now reverse biased, and the output diode is now forward biased, all the charge that accumulated in Cpfn is discharged through the output diode, producing the output pulse from the laser diode.

Where I disagree with the data sheet is the direction of the arrow showing "electron flow". It shows the flow of electrons as moving from the output diode's cathode to it's anode. They seem to be depicting electrons flowing towards the negative terminals of the output diode and capacitor! Surely this arrow is pointing in the wrong direction...or have I got the wrong end of the stick?

Thanks in advance for your input!
 

Attachments

  • circuit.jpg
    circuit.jpg
    14.7 KB · Views: 1,753
Engineering news on Phys.org
At least in a regular diode the actual flow of electrons is from the cathode to anode, and that's also in agreement with your description of how the circuit works; i.e. the cap discharges through D3, with current flow in the direction of the arrow.
 
Hi,

thanks for your reply. Glad to have someone agree with me! I'm still naive enough to have this voice in my head tell me that if it's in something like a data sheet, it must be right! ;)
 
Hi,

Is there some commercial product according to this data sheet?
 
Galiupatiket said:
Hi,

Is there some commercial product according to this data sheet?

Yes. It's from a commercial laser diode driver. The company is www.directedenergy.com and it's from a PCO-7110 Laser Diode Driver Module.
 
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
While I was rolling out a shielded cable, a though came to my mind - what happens to the current flow in the cable if there came a short between the wire and the shield in both ends of the cable? For simplicity, lets assume a 1-wire copper wire wrapped in an aluminum shield. The wire and the shield has the same cross section area. There are insulating material between them, and in both ends there is a short between them. My first thought, the total resistance of the cable would be reduced...
I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...

Similar threads

Replies
14
Views
2K
Replies
6
Views
3K
Replies
10
Views
2K
Replies
32
Views
3K
Replies
12
Views
2K
Replies
16
Views
7K
Replies
5
Views
3K
Back
Top