Recommend me h-bridge ic for stepper motor

AI Thread Summary
The discussion focuses on finding a suitable H-bridge IC for a stepper motor with specific requirements, including an output rating of 4-5A and control via at least two digital PWM inputs. The motor in question is a 23HS8630 model with a current rating of 3A per phase and specific inductance and resistance values. One participant suggests using a parametric search on IC manufacturer websites, while another expresses difficulty in finding a definitive answer. There is a light-hearted exchange about the search process and the challenges of building a custom solution. The conversation remains focused on identifying the right H-bridge IC for the specified stepper motor.
elementHTTP
Messages
21
Reaction score
0
Recommend me h-bridge ic
-output rated for 4~5A
- can be controlled by min 2 digital PMW inputs
- optional* half step
- optional* SMD

23HS8630 stepper motor specs :
6 wires ,
3A / phase ,
1.0 Ohm / phase ,
1.8 mH / phase


Thanks :D
 
Engineering news on Phys.org
Have you tried doing a parametric search on any of the IC manufacturer's websites, digikey, etc?
 
Last edited:
Why don't you do a parametric search on your favorite IC manufacturer's website like a normal person?

So i did and i didnt get definitive answer so i am asking for help :D ( building custom is another option ) sry if i wasted your time
 
Haha, I see you are responding to my initial response which I immediately ninja-edited into a more presentably form. You're too quick for me! I should have stayed in bed.
 
:D
well let's keep it civil :D
 

Thread 'Underwater piezoelectric sensor array receive sensitivity'

Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
View full post »

Thread 'Following up on the recent thread about Earth Resistance measurements'

I have recently moved into a new (rather ancient) house and had a few trips of my Residual Current breaker. I dug out my old Socket tester which tell me the three pins are correct. But then the Red warning light tells me my socket(s) fail the loop test. I never had this before but my last house had an overhead supply with no Earth from the company. The tester said "get this checked" and the man said the (high but not ridiculous) earth resistance was acceptable. I stuck a new copper earth...
View full post »

Thread 'Question about bonding ground and neutral'

I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...
View full post »

Similar threads

Relay Control of Induction Motors
Replies
5
Views
783
What is the optimal voltage for a stepper motor?
Replies
5
Views
2K
Stepper Motor Anatomy and Logic
Replies
2
Views
2K
H-Bridge troubles (driving a stepper motor)
Replies
1
Views
3K
Making an Arduino controlled H-bridge
Replies
9
Views
4K
Is ULN2064B Safe for 24V Stepper Motors?
Replies
5
Views
3K
What are some options for H-bridge ICs to power 12V 3.6A loads?
Replies
2
Views
2K
Connecting an L293D H-Bridge to a DC Motor: Advice Needed
Replies
1
Views
1K
Having trouble with L298N H-Bridge IC
Replies
1
Views
2K
Stepper Motor Controller only working on a particular power suppy?
Replies
24
Views
9K

Hot Threads

Recent Insights

Back
Top