Sniper Projectile Motion: Trajectory and Impact Analysis

AI Thread Summary
A sniper fires a bullet at 120 m/s at a 30° angle from a 35 m high parking garage, resulting in a flight time of approximately 12.8 seconds before hitting the ground. The horizontal distance traveled by the bullet is calculated to be around 1,331.2 meters. The vertical component of the bullet's velocity at impact is found to be -65.5 m/s, leading to an impact angle of approximately 57.79° from the vertical. The discussion emphasizes the separation of horizontal and vertical motion components and the use of kinematic equations to analyze projectile motion. The calculations and methodology presented are confirmed as correct by participants in the thread.
Inferior Mind
Messages
14
Reaction score
0
A sniper fires a bullet at 120 m/s at 30° above the horizontal from the roof top of a 35 m high parking garage. If the bullet strikes the level ground beside the parking garage:

How long was the bullet in the air?

How far from the base of the parking garage did the bullet land?

At what angle did the bullet land?

g= -9.8 m/s^2
Vi= 120 m/s @ 30 degree incline
h=35 m
Vx= 120Cos30 = 140 m/s
Vy= 120Sin30 = 60 m/s
 
Physics news on Phys.org
Use the following equation to find time:
Δy = v_oyt + 1/2at^2,
where Δy = - 35, v_0y = 60, a = -9.8m/s^2
 
First off, doesn't a Muzzle Velocity seem a bit low at 120 m/s? -_-

Alright, so it looks like I end up with a Quadratic and solve for both values.

0 = -4.9t^2 + 60t + 35

t = -.55s and 12.8s

But there can't be negative time, amiright ?

And I am unsure about the Total change in the horizontal distance.

Would ~ Dx = Vx(t) ? [x represents the change in the horizontal or x-axis]

= (104 m/s)12.8 s
= 1,331.2 m
 
Ok good, I'm assuming you did the quadratic right.
If t is 12.8 s.
Simply use the same equation again:
Δx = v_oxt + 1/2at^2,
Here a = 0, so the equation becomes:
delta x = v_oxt
You have both of those.
It seems like you've done it right.
Good job.
 
It's uses a spring to fire the bullet!

The point was to separate horizontal (x) and vertical (y) components.

With straight line constant acceleration a, velocity is at+ v_0 and distance traveled is (1/2)at^2+ v_0t+ s_0<br /> <br /> In this problem, <b>vertically<b>, the acceleration is -g= -9.82 m/s^2, approximately, so that y= -4.91t^2+ 60t+ 35 where I have chosen the "0" height to be on the ground, at the bottom of the building. The bullet hits the ground, then, when -4.91t^2+ 60t+ 35= 0. Yes, that will have two roots, one negative and one positive. Yes, the positive root is the one you want.<br /> <br /> <b>Horizontally</b>, the acceleration is 0 so the equation is x= 140t where I have chosen x= 0 as the starting point, horizontally. To find how far the bullet goes horizontally, set t equal to the value you got before for the time the bullet is in the air.</b></b>
 
Alright, so assuming everything so far is correct, my only issue has been the angle at which the bullet hits the ground.

If Tan θ = O / A then could I use the components for Sin and Cos ?

My text says that I should change the Velocity of the Vertical Component by using:

Vr = Vy + aΔt
= 60 m/s + (-9.8 m/s)12.8s
= -65.5 m/s

Since this becomes the Hypotenuse of the triangle at the moment of impact it becomes positive.

... so Tan^-1(104/65.5) = 57.79° from the Vertical.

Can someone double check if this is an acceptable answer?

Thanks in advance.
 
Kindly see the attached pdf. My attempt to solve it, is in it. I'm wondering if my solution is right. My idea is this: At any point of time, the ball may be assumed to be at an incline which is at an angle of θ(kindly see both the pics in the pdf file). The value of θ will continuously change and so will the value of friction. I'm not able to figure out, why my solution is wrong, if it is wrong .
Thread 'Voltmeter readings for this circuit with switches'
TL;DR Summary: I would like to know the voltmeter readings on the two resistors separately in the picture in the following cases , When one of the keys is closed When both of them are opened (Knowing that the battery has negligible internal resistance) My thoughts for the first case , one of them must be 12 volt while the other is 0 The second case we'll I think both voltmeter readings should be 12 volt since they are both parallel to the battery and they involve the key within what the...
Thread 'Correct statement about a reservoir with an outlet pipe'
The answer to this question is statements (ii) and (iv) are correct. (i) This is FALSE because the speed of water in the tap is greater than speed at the water surface (ii) I don't even understand this statement. What does the "seal" part have to do with water flowing out? Won't the water still flow out through the tap until the tank is empty whether the reservoir is sealed or not? (iii) In my opinion, this statement would be correct. Increasing the gravitational potential energy of the...
Back
Top