What Causes Strong Surface Turbulence in Thermal Baths?

AI Thread Summary
Strong surface turbulence in thermal baths is primarily caused by the energy from whirlpool jets, which creates significant upward forces that affect individuals submerged in water. The buoyancy experienced while submerged alters a person's center of gravity, making them more susceptible to the currents generated by the jets. Despite the jets being small and seemingly weak at the outlet, their impact is amplified at the surface due to the water's low friction and the immediate effect of the jets when activated. The discussion highlights that even with a portion of the body above water, the turbulence can still be overpowering. Understanding these dynamics can enhance the experience in thermal baths.
arcnets
Messages
493
Reaction score
0
Hi all,
the other day I was in a thermal bath where they had some whirlpool jets at the bottom of a basin about breast-deep. I was standing right over the jets, and the turbulence in the water was so strong at the surface, that I couldn't stand straight but was forced to sway back and forth and was almost washed away from the position of the jets.
I probed the ground with my toes and expected the position of the outlets to be easily detectable by a sharp vertical jet of water. But nothing! Next, I located the outlets by eye (there were maybe 5 or 6 of them, of ~1/4 inch diameter each), and put my toe on one. There was almost nothing to be felt, and I could easily block the jet with my toe.
Forces seem to be large only when close to the surface, and very small deeper down. Any physical explanation of this?
 
Engineering news on Phys.org
well I may not have the physics explanation, but I can give you the common sense one. basically being submerged in water not only makes you lighter due to buoyancy, but changes your center of gravity. And since your center of gravity is higher, you're more suceptable to currents and other objects in motion. Basically the energy from the jets has more effect because of your submergence.

Anyone else? Does that make sense, sound partially right, with some adjustment, or do I need to lay off the beer?:wink:
 
Only that the friction of the water rotating in the tub must have been pretty low so that the rate of rotation built up over time.
 
Thanks indeed for your response!

Zantra,
yes I agree it's much easier for the water to move me upwards when most of me is submerged. But my head & shoulders were still out of the water, so the remaining gravity was still (say) 4 or 5 kg's or so, and I couldn't feel anything like that when probing the jet with my toe. There was almost nothing to be felt.

Tyger,
maybe my wording was bad, there wasn't any rotating water in a tub. It was a big basin (say 5m x 15m or so), and there was 5 or 6 jets at the center of that, at the bottom, closer than, say, 30 cm together, with the water going up vertically, and I was standing over that. Plus, the effect was immediately there as soon as the jets were powered up.
 
Hi all, I have a question. So from the derivation of the Isentropic process relationship PV^gamma = constant, there is a step dW = PdV, which can only be said for quasi-equilibrium (or reversible) processes. As such I believe PV^gamma = constant (and the family of equations) should not be applicable to just adiabatic processes? Ie, it should be applicable only for adiabatic + reversible = isentropic processes? However, I've seen couple of online notes/books, and...
Thread 'How can I find the cleanout for my building drain?'
I am a long distance truck driver, but I recently completed a plumbing program with Stratford Career Institute. In the chapter of my textbook Repairing DWV Systems, the author says that if there is a clog in the building drain, one can clear out the clog by using a snake augur or maybe some other type of tool into the cleanout for the building drain. The author said that the cleanout for the building drain is usually near the stack. I live in a duplex townhouse. Just out of curiosity, I...
I have an engine that uses a dry sump oiling system. The oil collection pan has three AN fittings to use for scavenging. Two of the fittings are approximately on the same level, the third is about 1/2 to 3/4 inch higher than the other two. The system ran for years with no problem using a three stage pump (one pressure and two scavenge stages). The two scavenge stages were connected at times to any two of the three AN fittings on the tank. Recently I tried an upgrade to a four stage pump...
Back
Top