What is the composition of exhaust fumes from petrol and diesel engines?

AI Thread Summary
Conventional petrol engines primarily emit nitrogen (N2), oxygen (O2), carbon dioxide (CO2), and water vapor, with carbon monoxide (CO) varying based on the air-fuel ratio. Diesel engines produce similar gases but also generate significant particulate matter, including soot and sulfur compounds. The levels of sulfur oxides (SO2), nitrogen oxides (NOx), and hydrocarbons (HC) are present in variable quantities, often measured in parts per million (ppm). The composition of exhaust gases is influenced by engine type, operational conditions, and fuel quality. Understanding these emissions is crucial for addressing environmental impacts and improving engine efficiency.
Aquafire
Messages
48
Reaction score
1
In regards to two types of engines..

What gases (by percentage) are to be found in conventional petrol driven internal combustion engines, such as found in cars ?

What gases (by percentage) are to be found in conventioanl diesel driven internal combustion engines, such as found in trucks ?

I have tried to search for an accurate breakdown of the two, but ploughing through the internet has left me more confused than clarified.

So, if any of you guys knows for sure...then please help me out..

Thanks in advance..

Aqua

Ps...

Mods, if you feel that this thread should be in chemistry, feel free to move it...
 
Engineering news on Phys.org
Depends quite a lot on the engine type, purpose, and how it's being run. This is a complex field, and (as you're probably aware), a huge amount of engineering work is done in this field.

In brief, there are thousands of different chemicals found in engine-out exhaust gases for both Diesel and petrol engines. The bulk of the gaseous emissions are made up of N2, O2, CO2, and water vapour (and maybe some CO). Typically, the N2 level will not change much before/after the combustion event. CO2, CO and O2 levels are all relative, and depend on the air fuel ratio. Lean operation will give high O2, moderate CO2, and low CO; where rich operation will give very low O2, moderate CO2, and very high CO.

Now, SO2, NOx and hydrocarbons are all pretty much universally present, but in very variable quantities (and these quantities are measured in ppm, rather than %). Sulphur compounds are a feature of sulphur in the fuel (which is why you now see low sulphur fuel), NOx is from atmospheric air, and is a feature of high peak cylinder temperatures; and HC are a result of incomplete combustion for whatever reason. Other components (notably alcohols and aldehydes) are present in smaller quantities still.

Diesel engines typically have high levels of particulate matter within the exhaust (as compared petrol engines). This particulate matter comprises of soot and sulphur compounds (from lube oil and fuel), all kinds of organic matter, and varying amounts of metals. Again, these are in tiny amounts compared with the main gaseous components.

Does this help?
 
Last edited:
Posted June 2024 - 15 years after starting this class. I have learned a whole lot. To get to the short course on making your stock car, late model, hobby stock E-mod handle, look at the index below. Read all posts on Roll Center, Jacking effect and Why does car drive straight to the wall when I gas it? Also read You really have two race cars. This will cover 90% of problems you have. Simply put, the car pushes going in and is loose coming out. You do not have enuff downforce on the right...
I'm trying to decide what size and type of galvanized steel I need for 2 cantilever extensions. The cantilever is 5 ft. The space between the two cantilever arms is a 17 ft Gap the center 7 ft of the 17 ft Gap we'll need to Bear approximately 17,000 lb spread evenly from the front of the cantilever to the back of the cantilever over 5 ft. I will put support beams across these cantilever arms to support the load evenly
Thread 'What's the most likely cause for this carbon seal crack?'
We have a molded carbon graphite seal that is used in an inline axial piston, variable displacement hydraulic pump. One of our customers reported that, when using the “A” parts in the past, they only needed to replace them due to normal wear. However, after switching to our parts, the replacement cycle seems to be much shorter due to “broken” or “cracked” failures. This issue was identified after hydraulic fluid leakage was observed. According to their records, the same problem has occurred...
Back
Top