Calculating the pH of CO2 dissolved in 1l of water

  • Thread starter Thread starter skaai
  • Start date Start date
  • Tags Tags
    Co2 Ph Water
AI Thread Summary
The discussion revolves around calculating the pH of a solution where carbon dioxide is dissolved in water at equilibrium. The setup involves 1 liter of water in a 100% carbon dioxide atmosphere at 25°C, leading to a calculated pH of approximately 3.92. Key calculations include determining the number of moles of dissolved CO2 and applying the pKa of carbonic acid to find the concentration of hydrogen ions. The participants acknowledge the complexity of accurately measuring carbonic acid concentration, often assuming all dissolved CO2 is in this form for practical calculations. Overall, the calculations appear sound, and the result is deemed reasonable for the given conditions.
skaai
Messages
16
Reaction score
0
OK folks,
first of all, let me thank those of you who have helped me with previous questions... perhaps this is why I keep coming back!

This time, I'm just asking those of you who are better than I am at this if I did this right and thus, got the correct result. I think I did, but since this is not a homework problem, I have no way of checking my answer...

I set up my problem like this (see the attached diagram):

Imagine our system has a beaker with 1 liter of water and is enclosed in a constant-pressure (of 1 atm.) atmosphere of 100% carbon dioxide at 25°C. We let the carbon dioxide come to equilibrium with the water so the maximum dissolves. What would the resultant pH be?

What do we know?
  • the pKa of carbonic acid is 6.367
  • the solubility of carbon dioxide in water at 25ºC 1atm is 1.45 gram/liter
  • we have 1 liter of water
What is the reaction?
CO2 + 2H2O → H2CO3 + H2O → HCO3- + H3O+
  • the number of moles of carbon dioxide that dissolve in water at equilibrium will equal the number of moles of carbonic acid in solution.
1.45 g. CO2\frac{1 mol.}{44.01 g.}= 0.032947 mol. CO2

Calculate using a RICE table (see the attached image table):
Convert pKa to Ka: 10-pKa = Ka → 10-6.367 = Ka
Ka (10-6.367) = \frac{[A-][H+]}{[HA]} = \frac{(x)(x)}{(0.0329-x)}​
can we apply the "rule of 500?":
Rule of 500: if \frac{[HA]}{Ka}>500, ignore any nonzero changes in "x"​
\frac{0.0329}{1x E-6.367}=76,594 >> 500 so yes.​
simplify Ka:
10-6.367=\frac{x²}{0.0329}​
x²=10-6.367(0.0329)=1.41317x10-8
x=√1.41317x10-8=1.18877x10-4=[H+]​
pH = -log[H+]=-log(1.18877x10-4)=3.9249≈3.92

so the lowest the pH can go in 1 liter of water in equilibrium with 100% CO2 at 25ºC and 1 atmosphere pressure is 3.92.

It sounds like a reasonable number, or did I totally mess something up somewhere?
thanks so much for any help on this!
 

Attachments

  • CO2 and Water.jpg
    CO2 and Water.jpg
    19.1 KB · Views: 1,906
  • H2CO3 Dissociation RICE Table.png
    H2CO3 Dissociation RICE Table.png
    3.3 KB · Views: 1,863
Chemistry news on Phys.org
Looks OK to me.

Note that actually we don't know what is the concentration of carbonic acid in water - we can measure solubility and pH, but that allows only to calculate equilibrium constant for the overall reaction

H2O + CO2 <-> H+ + HCO3-

but not for two separate ones:

H2O + CO2 <-> H2CO3

H2CO3 <-> H+ + HCO3-

We often do assume all carbon dioxide dissolved is present in the form of carbonic acid, that yields commonly known Ka1 value. As it yields a correct calculation results we simply don't care about reality.
 
  • Like
Likes 1 person
I see your point about carbonic acid... it's so mysterious, but all we can do is like with dark matter... infer its there from the effects...

thanks so much for the once-over!
 
I want to test a humidity sensor with one or more saturated salt solutions. The table salt that I have on hand contains one of two anticaking agents, calcium silicate or sodium aluminosilicate. Will the presence of either of these additives (or iodine for that matter) significantly affect the equilibrium humidity? I searched and all the how-to-do-it guides did not address this question. One research paper I found reported that at 1.5% w/w calcium silicate increased the deliquescent point by...
I'm trying to find a cheap DIY method to etch holes of various shapes through 0.3mm Aluminium sheet using 5-10% Sodium Hydroxide. The idea is to apply a resist to the Aluminium then selectively ablate it off using a diode laser cutter and then dissolve away the Aluminium using Sodium Hydroxide. By cheap I mean resists costing say £20 in small quantities. The Internet has suggested various resists to try including... Enamel paint (only survived seconds in the NaOH!) Acrylic paint (only...
Back
Top