Can a 1.3 hp Engine Power Our Prototype Car?

AI Thread Summary
A 1.3 hp engine may be suitable for the prototype car, which weighs 120 kg and reaches a maximum speed of 13.88 m/s, given that calculated net power losses amount to 1.234 hp. Key considerations include rolling resistance, road gradient, and drag, with specific formulas provided for each loss. Additional factors such as drivetrain friction, safety margins, and acceleration needs were raised as potential oversights in the initial calculations. To determine the power losses through transmission, overall efficiency should be calculated based on the number of gear sets and their respective efficiencies. Ultimately, the engine must operate under optimal conditions to ensure adequate power delivery to the wheels.
Carvinos
Messages
7
Reaction score
0
Hello!
Actually i want to find the required power of an a single cylinder air cooled 4 stroke OHV engine. i have calculated three power losses, power loss against road gradient (Pg), rolling resistance (Pr) and drag (Pd) using the following formulae:
Pg=M*g*v*grad=1.095 hp
M(mass of the prototype car)=120kg, g=9.8 m/s^2, v(prototype car velocity)=13.88 m/s, road gradient= 5% (0.05)
Pr=RRC*M*g*v=0.109 hp
RRC (rolling resistance coefficient)=0.005 for a bicycle tire we are using in our prototype car
Pd=0.5*rho*v^3*Cd*A = 0.030 hp
rho=1.099 kg/m^3, Cd (Coefficient of drag)=0.04 in case of our prototype car, A=0.384 m^2
Net power losses=Pg+Pr+Pd=1.234 hp.
Now please tell me can i use an engine of 1.3 hp of 35cc volumetric capacity in our prototype three wheeled car. Generator is the only accessory that will be connected with the engine to charge the battery.13.88 m/s will be the max. speed of our prototype car, 120 kg is the mass of the prototype with driver. reply soon please
 
Engineering news on Phys.org
Did you calculate the rolling resistance for all wheels?
Have you applied a safety factor, and an allowance for acceleration (and not just travel at a constant speed)?
Have you considered friction in your drivetrain?
Have you considered conversion losses through the powertrain (including your 'generator'?)
Is your engine going to be operating at optimum conditions for 1.3hp?
 
ok.thnx.tell me please the procedure of how to calculate the power losses of engine through transmission.
 
Carvinos said:
ok.thnx.tell me please the procedure of how to calculate the power losses of engine through transmission.

For every gear set or belt drive set, assume 95% efficiency. For every chain drive set, assume 92% efficiency. Multiply all of them for overall efficiency.

Ex.:

if the power of your engine goes through 3 gear sets before reaching the wheels, your overall efficiency would be 0.95*0.95*0.95 = 0.857. So if you need 1.234 hp at the wheel, you need 1.234 / 0.857 = 1.44 hp at the engine.
 
I need some assistance with calculating hp requirements for moving a load. - The 4000lb load is resting on ball bearing rails so friction is effectively zero and will be covered by my added power contingencies. Load: 4000lbs Distance to travel: 10 meters. Time to Travel: 7.5 seconds Need to accelerate the load from a stop to a nominal speed then decelerate coming to a stop. My power delivery method will be a gearmotor driving a gear rack. - I suspect the pinion gear to be about 3-4in in...
How did you find PF?: Via Google search Hi, I have a vessel I 3D printed to investigate single bubble rise. The vessel has a 4 mm gap separated by acrylic panels. This is essentially my viewing chamber where I can record the bubble motion. The vessel is open to atmosphere. The bubble generation mechanism is composed of a syringe pump and glass capillary tube (Internal Diameter of 0.45 mm). I connect a 1/4” air line hose from the syringe to the capillary The bubble is formed at the tip...
Thread 'Calculate minimum RPM to self-balance a CMG on two legs'
Here is a photo of a rough drawing of my apparatus that I have built many times and works. I would like to have a formula to give me the RPM necessary for the gyroscope to balance itself on the two legs (screws). I asked Claude to give me a formula and it gave me the following: Let me calculate the required RPM foreffective stabilization. I'll use the principles of gyroscopicprecession and the moment of inertia. First, let's calculate the keyparameters: 1. Moment of inertia of...
Back
Top