Chemistry Help: Neutralizing HCl & H3PO4 Solutions

  • Thread starter Thread starter TJSR
  • Start date Start date
  • Tags Tags
    Chemistry
AI Thread Summary
To determine how many grams of Mg(OH)2 are needed to neutralize 25 mL of 0.10 M HCl, first calculate the moles of HCl by multiplying the volume (0.025 L) by its molarity (0.10 M), resulting in 0.0025 moles. The balanced reaction shows a 1:2 ratio of Mg(OH)2 to HCl, so divide the moles of HCl by 2 to find 0.00125 moles of Mg(OH)2 required. Using the molecular weight of Mg(OH)2 (42.32 g/mol), the mass needed is calculated as 0.00125 moles multiplied by 42.32 g/mol, yielding approximately 0.0529 grams.For the second problem, to neutralize 15 mL of 0.20 M H3PO4, the balanced equation indicates a 1:3 ratio with NaOH.
TJSR
Messages
2
Reaction score
0
HELP!

I need to know how to figure these problems out, while showing all
work so I can follow the steps...thanks for the help!

1. how many grams of Mg(OH)2 (2 is a subscript) will be needed to neutralize
25ml of stomach acid if stomach acid is 0.10 M HCl?

2. How many ml of a 0.10 NaOH solution are needed to neutralize 15ml of 0.20
M H3PO4 (subscripts) solution?
 
Chemistry news on Phys.org
Please show your work first.
 
All i can say if please use:

Ma x Mb / Va x Vb transpose for what you need.
 
for number 1:

find out how many moles of HCl are in 25mL of a 0.10M solution by multiplying volume times molarity.

M HCl = 25mL x 1L/1000mL x 0.10mol / 1L

next calculate how many mL of xM Mg(OH)_2 solution contains the calculated number of moles of HCl. (I'm assuming you were given the molarity of Mg(OH)_2)

M HCl x 1L soln / M Mg(OH)_2 = x L of soln

convert L to mL, then you can multiply the answer by magnesium hydroxide's specific gravity (2.36) to get the amount in grams.


number 2 is the same approach but the answer is left in mL.
 
Is it wrong here to assume that the production of Magnesium Chloride and water is a "neutralization" of the HCl? It sounds like a relatively elementary [HS Chem or Intro to Chem] level question, so a balanced eqn. and mole ratios could find how many grams of magnesium hydroxide are needed to completely react with all .025 L of HCl ... thus ridding the acid. Too simplified?
 
Question one:

“How many grams of Mg(OH)2 (2 is a subscript) will be needed to neutralize
25ml of stomach acid if stomach acid is 0.10 M HCl?”

Display reaction equation (balanced) (Step 1)

Mg(OH)2+2HCl-->MgCl2+2H2O

1 to 2 ratio:

25ml of 0.10 M (INITIAL CONCENTRATION BEFORE DILUTION) of HCl (Step 2)

Concentration (M) = Number of moles / Volume

Therefore number of moles = concentration x volume (Step 3)

25ml = 0.025 dm^3

Number of moles = 0.10 x 0.025 = 0.0025 moles of HCl

Now back to Step 1, there is a ratio of 1:2, so we must divide answer by 2:

Moles in ratio = 0.0025 / 2 = 0.00125 (Step 4)

Now to get mass (amount in grams) (Step 5)

Mass (w) = Number of moles x Mr (Molecular mass)

Mr of Mg(OH)2 = 42.320g

Therefore w = 0.00125 x 42.320 = 0.0529g

So 0.0529g of Mg(OH)2 was needed to neutralise 0.0025 moles of Stomach acid (HCl).

Question 2:

“How many ml of a 0.10 NaOH solution are needed to neutralize 15ml of 0.20
M H3PO4 (subscripts) solution?”

H3PO4 + 3NaOH --> Na3PO4 + 3H2O (Step 1)

As we can deduce from the above equation there is a 1:3 ratio (Step 2)

Concentration (M) = Number of moles / Volume

Therefore number of moles = concentration x volume (Step 3)

15ml = 0.015 dm^3

0.20 x 0.015 = 0.003 moles of H3PO4

Since the ratio is 1:3 we must multiply the number of moles of H3PO4 by 3. (Step 4)
Mole(3NaOH) = 0.003 x 3 = 0.009.

Concentration (M) = Number of moles / Volume

Therefore Volume = Concentration x Number of moles: (Step 5)

Volume of (3NaOH) = 0.10 x 0.009 = 0.0009 dm^3

Volume in ml = dm^3 x 1000

Therefore volume of 3NaOH (in ml) = 0.0009 x 1000 = 0.9 ml of 3NaOH needed.
 
I want to test a humidity sensor with one or more saturated salt solutions. The table salt that I have on hand contains one of two anticaking agents, calcium silicate or sodium aluminosilicate. Will the presence of either of these additives (or iodine for that matter) significantly affect the equilibrium humidity? I searched and all the how-to-do-it guides did not address this question. One research paper I found reported that at 1.5% w/w calcium silicate increased the deliquescent point by...
I was introduced to the Octet Rule recently and make me wonder, why does 8 valence electrons or a full p orbital always make an element inert? What is so special with a full p orbital? Like take Calcium for an example, its outer orbital is filled but its only the s orbital thats filled so its still reactive not so much as the Alkaline metals but still pretty reactive. Can someone explain it to me? Thanks!!
I'm trying to find a cheap DIY method to etch holes of various shapes through 0.3mm Aluminium sheet using 5-10% Sodium Hydroxide. The idea is to apply a resist to the Aluminium then selectively ablate it off using a diode laser cutter and then dissolve away the Aluminium using Sodium Hydroxide. By cheap I mean resists costing say £20 in small quantities. The Internet has suggested various resists to try including... Enamel paint (only survived seconds in the NaOH!) Acrylic paint (only...
Back
Top