Damped Oscillations in an RLC circuit

AI Thread Summary
The discussion revolves around calculating the charge on a capacitor in a damped RLC circuit after five complete cycles. The circuit consists of a 7.2 ohm resistor, an 11.9 H inductor, and a 3.4*10^-6 F capacitor, with an initial charge of 6.3*10^-6 C and zero current. The angular frequency has been determined to be 157.2122 rad/s, but there is confusion regarding its relationship to time for multiple cycles. It is clarified that the time for five cycles can be calculated as 10π divided by the angular frequency. Understanding angular frequency as radians per second is emphasized, aiding in the calculation of the period and subsequent time for multiple cycles.
electrohau5
Messages
13
Reaction score
0

Homework Statement



A single loop circuit consists of a 7.2 ohm resistor, a 11.9 H inductor, and a 3.4*10^-6 F capacitor. Initially the Capacitor has a charge of 6.3*10^-6 C and the current is zero. Find the charge on the capacitor N complete cycles later for N=5.

Homework Equations



2. Homework Equations
q=Qe^(-Rt/2L)cos(wt + p), where p is the phase constant and w is the angular frequency.

The Attempt at a Solution



I have already found angular frequency to be 157.2122, but how do I relate this to time it takes to make 5 cycles? I do not fully understand the definition of w.
(the idea of angular frequency has always been quite confusing to me as I have not yet taken mechanics and am doing E&M first)
 
Physics news on Phys.org
electrohau5 said:

Homework Statement



A single loop circuit consists of a 7.2 ohm resistor, a 11.9 H inductor, and a 3.4*10^-6 F capacitor. Initially the Capacitor has a charge of 6.3*10^-6 C and the current is zero. Find the charge on the capacitor N complete cycles later for N=5.


Homework Equations



2. Homework Equations
q=Qe^(-Rt/2L)cos(wt + p), where p is the phase constant and w is the angular frequency.

The Attempt at a Solution



I have already found angular frequency to be 157.2122, but how do I relate this to time it takes to make 5 cycles? I do not fully understand the definition of w.
(the idea of angular frequency has always been quite confusing to me as I have not yet taken mechanics and am doing E&M first)

Angular frequency is radians per second. So 1 rotation per second is 2pi radians per second. Etc.

If you know w which = 2pi * f, then period T = 1/f as you know I'm sure.
 
electrohau5 said:
would the time it takes be equal to 5 times the period, so 10pi/w?

Yes.

ehild
 
electrohau5 said:
would the time it takes be equal to 5 times the period, so 10pi/w?

Yes again.
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...

Similar threads

Replies
3
Views
596
Replies
3
Views
2K
Replies
3
Views
3K
Replies
5
Views
5K
Replies
22
Views
2K
Replies
14
Views
3K
Replies
8
Views
2K
Replies
4
Views
3K
Replies
2
Views
3K
Back
Top