Extracting CuCl2 from used PCB etchant.

  • Thread starter Thread starter physicscience
  • Start date Start date
  • Tags Tags
    Pcb
AI Thread Summary
The discussion centers on the extraction of copper chloride (CuCl2) from used PCB etchant, specifically ferric chloride (FeCl3). The original poster seeks methods to separate CuCl2 from a solution that also contains FeCl2 after reacting copper with ferric chloride. There is uncertainty about the effectiveness of boiling for separation. The poster expresses a primary interest in extracting copper chloride but is also open to methods for recovering copper and converting it into copper chloride. Alternatives to ferric chloride are mentioned, but the poster prefers to stick with ferric chloride due to its availability.
physicscience
Messages
4
Reaction score
0
Greetings all. I was wondering if any of you would know how exactly to extract copper chloride (CuCl2) from a solution of used pcb etchant. I know that when you react ferric chloride (the initial etchant) with copper, the products are FeCl2 and CuCl2 dissolved in a dark colored solution but how would i separate the 2 from there? I don't think boiling would help. If any of you know that would be great. Thanks.
 
Chemistry news on Phys.org
Are you interested just in recovering the copper? Or the copper chloride?
 
Bystander said:
Are you interested just in recovering the copper? Or the copper chloride?
I'm interesting in extracting the copper chloride but if that if not directly possible, I would also like to know how to recover the copper and then turn it into copper chloride.
 
Are you interested in an alternative to ferric chloride? No, I haven't tried it. http://m.instructables.com/id/Stop-using-Ferric-Chloride-etchant!--A-better-etc/
 
NascentOxygen said:
Are you interested in an alternative to ferric chloride? No, I haven't tried it. http://m.instructables.com/id/Stop-using-Ferric-Chloride-etchant!--A-better-etc/
So far, ferric chloride is the easiest obtainable etching solution I have at my disposal.
 

Thread 'Humidity of a saturated NaCl solution with anticaking additive'

I want to test a humidity sensor with one or more saturated salt solutions. The table salt that I have on hand contains one of two anticaking agents, calcium silicate or sodium aluminosilicate. Will the presence of either of these additives (or iodine for that matter) significantly affect the equilibrium humidity? I searched and all the how-to-do-it guides did not address this question. One research paper I found reported that at 1.5% w/w calcium silicate increased the deliquescent point by...
View full post »

Thread 'Resists for etching Aluminium with NaOH'

I'm trying to find a cheap DIY method to etch holes of various shapes through 0.3mm Aluminium sheet using 5-10% Sodium Hydroxide. The idea is to apply a resist to the Aluminium then selectively ablate it off using a diode laser cutter and then dissolve away the Aluminium using Sodium Hydroxide. By cheap I mean resists costing say £20 in small quantities. The Internet has suggested various resists to try including... Enamel paint (only survived seconds in the NaOH!) Acrylic paint (only...
View full post »

Similar threads

Copper (II) salts and SO2: a question
Replies
3
Views
3K
Solution Potential Witout Electrodes (Pourbaix diagram help)
Replies
1
Views
3K
What are the materials and methods for testing plastic levels in water?
Replies
5
Views
3K
How to remove epoxy resin from diesel fuel? A/B extraction? Distill?
Replies
7
Views
2K
Extracting carbohydrates from food dissolved in hydrochloric acid
Replies
3
Views
1K
Can I Use Electroforming with Copper to Etch PCBs Safely and Cheaply?
Replies
9
Views
3K
Help, I have made a huge mistake with copper sulfate!
Replies
11
Views
5K
Effect of particle size on boiling point in solution
Replies
6
Views
4K
How much electrical energy can be extracted from Iron in a cell?
Replies
3
Views
2K
Electrodialysis with different anions
Replies
1
Views
1K

Hot Threads

Recent Insights

Back
Top