Find the extra force required to maintain the speed of the belt

  • Thread starter Thread starter Doubell
  • Start date Start date
  • Tags Tags
    Belt Force Speed
AI Thread Summary
To maintain the speed of a conveyor belt moving at 2.0 m/s with coal falling at a rate of 540 tonnes per hour, the extra force required is calculated using Newton's second law. The mass flow rate of coal converts to 150 kg/s, and since the belt's velocity remains constant, there is no acceleration. The force needed to counteract the momentum change is determined by the rate of change of momentum, resulting in a force of 300 N. Both initial and final momentum calculations confirm this value. Therefore, the extra force required to maintain the belt's speed is 300 N.
Doubell
Messages
29
Reaction score
0

Homework Statement



coal is falling onto a conveyor belt at a rate of 540 tonnes every hour. the belt is moving horizontally at 2.0 ms-1. find the extra force required to maintain the speed of the belt. (1 tonne=1000kg.)



Homework Equations



F=m*a



The Attempt at a Solution



i tried to solve by saying that F=m*a. so to find force i would need the accelaration of the belt and multiply it by the mass of the coal. the acceleration is the rate of change of velocity so i would use the 2ms-1 as the final velocity and 0 ms-1 as the annitial subtracting 0 from two leaves 2 ms-1 and i divide by the rate of change of time which is 3600s.this leaves me with an accelaeration of 0.000556 ms/s^2 multiplying this by the mass of the coal 540000kg leaves 300 N. is this right
 
Physics news on Phys.org


I'm not too sure on that problem. What I think I can advise however is a few things.

You are trying to maintain the speed, this means that
final velocity and initial velocity are both 2 m/s which means that

v-v_0=at
2m/s - 2m/s = at
0=at

so there is no acceleration.

If you take the 540,000kg/h and convert it into seconds you get 150kg/s . So now you know how much the mass is increasing by per second and the acceleration.

Using dimensional analysis, we have 150 kg/s and 2.0 m/s , if we multiply these values, we get 300 kg.m/s^2 which is a Newton , so I believe the answer is 300 N like you suspected. However I would also check with others as I am not certain on this.
 


i just looked at it and found out another solution. in accordance to Newton's second law force = rate of change of momentum. the innitial momentum that occurred in 1 second would be 150kg *2 ms-1 (mass x velocity) which equals 300 kg ms-1 the final momentum that occurred in 3600 seconds would be 540000kg *2 ms-1.( the final and innitial velocities are the same) which = 1080000 kg ms-1. change in momentum = final momentum - innitial momentum this equals 1079700 kg ms-1. the change in time = T2-T1 = 3600s-1s which gives 3599s. Now in accordance to Newtons second law the rate of change of momentum = force this implies that change in momentum(1079700 kg ms-1) divided by change in time(3599s) = 300 kg m/s^2 =300N
 
Kindly see the attached pdf. My attempt to solve it, is in it. I'm wondering if my solution is right. My idea is this: At any point of time, the ball may be assumed to be at an incline which is at an angle of θ(kindly see both the pics in the pdf file). The value of θ will continuously change and so will the value of friction. I'm not able to figure out, why my solution is wrong, if it is wrong .
TL;DR Summary: I came across this question from a Sri Lankan A-level textbook. Question - An ice cube with a length of 10 cm is immersed in water at 0 °C. An observer observes the ice cube from the water, and it seems to be 7.75 cm long. If the refractive index of water is 4/3, find the height of the ice cube immersed in the water. I could not understand how the apparent height of the ice cube in the water depends on the height of the ice cube immersed in the water. Does anyone have an...
Back
Top