Finding work done by force of friction

AI Thread Summary
The problem involves calculating the work done by friction on a 4.0-kg block moving down a 37° incline while a horizontal force of 10 N is applied. The kinetic energies at points A and B are given as 10 J and 20 J, respectively. The approach involves using the work-energy theorem, where the total work done equals the change in mechanical energy. The calculations indicate that the frictional work should yield a negative value, but an error in sign was noted in the final result. Ultimately, the correct work done by friction is approximately -50 J.
Zipzap
Messages
32
Reaction score
0

Homework Statement


A 4.0-kg block is lowered down a 37° incline a distance of 5.0 m from point A to point B. A horizontal force (F = 10 N) is applied to the block between A and B as shown in the figure. The kinetic energy of the block at A is 10 J and at B it is 20 J. How much work is done on the block by the force of friction between A and B?

(I can't find a picture of this, but the block is being lowered down an incline going right, and the horizontal force is directly left, parallel to the ground)

Homework Equations



Ek = 0.5mv^2
Ep = mgh
(delta)E = Ef - Ei

The Attempt at a Solution



After some research, the answer is supposed to be -68 J

However, I'm stuck as to how I have to approach this problem. My initial idea was to determine the potential and kinetic energies of both A and B, and somehow use basic math and plug n' chug to get my answer. Is this the right approach?
 
Physics news on Phys.org
You know the initial KE of the block at "A". You also know the kinetic energy of the block at "B". The reduction in the potential energy (m*g* 5 * sin(37)) must cause in increase in KE of the block. The frictional force will dissipate the KE of the block and the component of the applied force along the incline (10 * cos(37)) to the left will dissipate the KE too.

So

KE(A) = 10

KE(B) = KE(A) + (m*g* 5 * sin(37)) - Frictional energy - (energy lost due to applied force along the incline tending to push it up along the incline ie - (10 * cos(37)) * 5

Plug in the numbers and get the Frictional energy
 
Hi Zipzap! :wink:

(have a delta: ∆ and try using the X2 and X2 icons just above the Reply box :wink:)

Use the work energy theorem …

total work done = change in mechanical energy …

what do you get? :smile:
 
Venkatg: Let me see if I have this down right...

KE(B) = KE(A) + PE(A) - F(fric) - W(app)

-F(fric) = KE(B) - KE(A) - PE(A) + W(app)

-F(fric) = 20 - 10 - 4*9.8*5sin37 + 10*5*cos37

Unfortunately, I get the right number, but I end up getting it positive and not negative. Where did I go wrong?
 
-fric = - 50 J (approximately)

so "fric" is 50 J. right ;-)?
 
TL;DR Summary: I came across this question from a Sri Lankan A-level textbook. Question - An ice cube with a length of 10 cm is immersed in water at 0 °C. An observer observes the ice cube from the water, and it seems to be 7.75 cm long. If the refractive index of water is 4/3, find the height of the ice cube immersed in the water. I could not understand how the apparent height of the ice cube in the water depends on the height of the ice cube immersed in the water. Does anyone have an...
Thread 'Variable mass system : water sprayed into a moving container'
Starting with the mass considerations #m(t)# is mass of water #M_{c}# mass of container and #M(t)# mass of total system $$M(t) = M_{C} + m(t)$$ $$\Rightarrow \frac{dM(t)}{dt} = \frac{dm(t)}{dt}$$ $$P_i = Mv + u \, dm$$ $$P_f = (M + dm)(v + dv)$$ $$\Delta P = M \, dv + (v - u) \, dm$$ $$F = \frac{dP}{dt} = M \frac{dv}{dt} + (v - u) \frac{dm}{dt}$$ $$F = u \frac{dm}{dt} = \rho A u^2$$ from conservation of momentum , the cannon recoils with the same force which it applies. $$\quad \frac{dm}{dt}...
Back
Top