How Is Angular Momentum Calculated for a Spinning Coin?

AI Thread Summary
The discussion focuses on calculating the angular momentum of a spinning coin using its moment of inertia and angular velocity. For part A, the correct formula to use is L = Iω, where I is the moment of inertia and ω is the angular velocity. In part B, the total angular momentum is found by adding the angular momentum from part A to the linear momentum calculated using the cross product of the radius and linear momentum. Part C requires a similar approach, taking into account the specified distance from the line of motion. The participants clarify the use of different formulas and the significance of vector directions in the calculations.
royguitarboy
Messages
16
Reaction score
0

Homework Statement



A 11 g coin of diameter 1.9 cm is spinning at 15 rev/s about a vertical diameter at a fixed point on a tabletop. A coin is a solid cylinder of length L and radius R, where L is negligible compared to R. Its moment of inertia is 1/4MR^2.

(A)What is its angular momentum about a point on the table 10 cm from the coin?

For the following questions, assume the coin spins about a vertical diameter at 15 rev/s while its center of mass travels in a straight line across the tabletop at 5 cm/s.

(B)What is the angular momentum of the coin about a point on the line of motion of the center of mass?

(C)What is the angular momentum of the coin about a point 10 cm from the line of motion?


Homework Equations



L=r*p
L=I *omega



The Attempt at a Solution



I tried L= r*p, where p equals m*v, and r was .1m, m was .011kg, and v was omega times the radius of the coin, which gave me an angular momentum of 9.85e-4. I know this isn't right.

For B should I add the angular momentum and the linear momentum?

And for C, if I can figure out A, I might be able to do that with C.
 
Physics news on Phys.org
royguitarboy said:
I tried L= r*p, where p equals m*v, and r was .1m, m was .011kg, and v was omega times the radius of the coin, which gave me an angular momentum of 9.85e-4. I know this isn't right.
That's the formula for the angular momentum of a point mass. It should read:
\vec{L} = \vec{r} \times \vec{p}

But that's not what you need for A. Use L = I \omega.

For B should I add the angular momentum and the linear momentum?
You need to add the angular momentum about the center of mass (the result of A) and the angular moment of the center of mass (using the linear momentum of the coin, as described by the first equation above). Be sensitive to the difference between B and C.
 
L = I \omega just gives me the angular momentum about the center of mass though right? How do I account for a distance 10cm from that point?
 
royguitarboy said:
L = I \omega just gives me the angular momentum about the center of mass though right?
Right.
How do I account for a distance 10cm from that point?
By calculating the angular momentum of the center of mass using the equation I gave:
\vec{L} = \vec{r} \times \vec{p}
 
Ok, now I'm really confused about this. For part A, I need to use \vec{L} = \vec{r} \times \vec{p} where p is mass times velocity?
 
royguitarboy said:
Ok, now I'm really confused about this. For part A, I need to use \vec{L} = \vec{r} \times \vec{p} where p is mass times velocity?
No, that's not needed for part A. All you need is L = I \omega.
 
ok I got you now. Now part B, I need to add part A to \vec{L} = \vec{r} \times \vec{p} ?
 
Exactly.
 
I'm confused as to which r, I should use for each part. In the the r X p part, the r is .05m right? So the total momentum is:

I(omega) + r X p

so I got 2.34e-5 + .05m X (.011)(\omega*(.019/2) ?
 
  • #10
The r to use in the r X p part is specified as 10 cm in parts a and c, the distance to the coin. Note that they don't bother to specify a distance in part b--there's a good reason for that. Also, the p is the linear momentum of the coin. Note also that r X p is a vector cross product--direction counts.
 
  • #11
Ok. I think I might have it. So for C, I need to add what I got in part B to the cross product of v and p, and subtract it, cause there should be two answers. Is that right? Well, I'm kind of confused about how to exactly do the cross product, we didn't really go over that.Edit: Never mind the above part. I got it!

You're a genius
 
Last edited:
Back
Top