How to find Tensile & compressive force

  • Thread starter Thread starter adilgrt007
  • Start date Start date
  • Tags Tags
    Force Tensile
AI Thread Summary
To determine tensile and compressive forces in a square bar, one must consider the area, weight, and density of the bar. The loading conditions and the configuration of the umbrella spokes, which may have a square cross-sectional area, are crucial for accurate calculations. The analysis involves applying principles of statics to assess forces at various points, particularly on one leg of the umbrella mechanism. Final-year mechanical engineering students should leverage their foundational knowledge from earlier coursework to tackle this problem effectively. Understanding the mechanics of pin joints and the geometry of the assembly is essential for deriving the required forces.
adilgrt007
Messages
4
Reaction score
0
hello guys i am student of mechanical engineering final year.i workout how to find tensile and compressive force of square bar & which point has a maximum forces workout. following parameters are known which are listed below.please solved my problem...

Parameters that are known

Area of the square bar
weight of the square bar
density of the square bar

Is there any formula please posted me...
 
Engineering news on Phys.org
How is the bar loaded?
 
sir i have a workout compressive forces on a umbrella spokes.what is a magnitude of these forces
 
A figure would be helpful...
 
So the spokes of the umbrealla have square CSA?
 
an umbrella mechanism is basically a radially-symetric assembly of sub-mechanisms

find the forces on one "leg" and go from there
the analysis is well within the capabilities of a final-year undergrad. use your training in statics.
it's basically a few bars, all pin joints, some intersecting at end points, others in midpoints

if that doesn't put you on the right track, review your second year mechanics training
 

Thread 'Bubble formation in 4 mm gap vessel'

How did you find PF?: Via Google search Hi, I have a vessel I 3D printed to investigate single bubble rise. The vessel has a 4 mm gap separated by acrylic panels. This is essentially my viewing chamber where I can record the bubble motion. The vessel is open to atmosphere. The bubble generation mechanism is composed of a syringe pump and glass capillary tube (Internal Diameter of 0.45 mm). I connect a 1/4” air line hose from the syringe to the capillary The bubble is formed at the tip...
View full post »
Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Scenario 1 (figure 1) A continuous loop of elastic material is stretched around two metal bars. The top bar is attached to a load cell that reads force. The lower bar can be moved downwards to stretch the elastic material. The lower bar is moved downwards until the two bars are 1190mm apart, stretching the elastic material. The bars are 5mm thick, so the total internal loop length is 1200mm (1190mm + 5mm + 5mm). At this level of stretch, the load cell reads 45N tensile force. Key numbers...
View full post »

Thread 'Find 3D Printer & Software Resources for Prototype Creation'

I'd like to create a thread with links to 3-D Printer resources, including printers and software package suggestions. My motivations are selfish, as I have a 3-D printed project that I'm working on, and I'd like to buy a simple printer and use low cost software to make the first prototype. There are some previous threads about 3-D printing like this: https://www.physicsforums.com/threads/are-3d-printers-easy-to-use-yet.917489/ but none that address the overall topic (unless I've missed...
View full post »

Similar threads

Signs of Tensile and Compressive Stresses
Replies
3
Views
5K
How does FEM software compute inertial forces?
Replies
13
Views
2K
Truss stress compressive/tensile stress
Replies
1
Views
6K
Looking to create a better frame for my e-motorcycle
Replies
10
Views
2K
Considerations for design of lead screw + guide rail set up
Replies
8
Views
4K
Finding Force and Energy from an indentation into a volume
Replies
24
Views
3K
I Big bang balloon?
Replies
5
Views
243
Find the force acting on the roller in the direction of the spring
Replies
14
Views
1K
Modeling Air Compression Cylinder
Replies
45
Views
5K
What is the Minimum Width of a Structural Steel Bar with Applied Axial Forces?
Replies
6
Views
2K

Hot Threads

Recent Insights

Back
Top