Isentropic Compression of Bose Gas with Subcritical Temperature T < T_c

  • Thread starter Thread starter tiger_striped_cat
  • Start date Start date
  • Tags Tags
    Compression Gas
AI Thread Summary
The isentropic compression of a Bose gas at subcritical temperatures (T < T_c) differs significantly from that of an ideal gas due to quantum interactions among particles. In a Bose gas, as the volume is reduced isothermically, the increased particle interactions can lead to the formation of a Bose-Einstein condensate (BEC), resulting in a phase transition and a decrease in entropy. The work done on the system must account for the energy required to form the BEC, which is calculated using the Gibbs free energy formula. This approach incorporates both energy and entropy changes, contrasting with the simpler ideal gas model. Thus, the work done in compressing a Bose gas involves complex interactions that must be considered for accurate calculations.
tiger_striped_cat
Messages
49
Reaction score
1
Problem: Consider a Bose gas with N particles is placed in a container with volume V and has temperature T, T < T_c. If the gas is compressed isothermically, what is the work done on the system when its volume is redused by a factor of 2.

Now I'm sure I could do this with an ideal gas, but how doe sthe problem change if it's a Bose Gas
 
Physics news on Phys.org
Okay, the exact solution is not easy.. but i can give you an approximation.. assume T<<T_c and ALL particle is stayed at the ground state, how the energy changed if the volume is reduced by half?? think about how the wave function related to the dimension of box and how is that related to energy...
 


The isentropic compression of a Bose gas with subcritical temperature T < T_c presents a unique problem compared to an ideal gas. This is because Bose gases exhibit different behavior due to their quantum nature and interactions between particles.

In an ideal gas, the particles do not interact with each other and the work done in an isentropic compression is simply given by the formula W = PΔV, where P is the pressure and ΔV is the change in volume. However, in a Bose gas, the particles can interact through attractive forces, leading to the formation of a Bose-Einstein condensate (BEC) at low temperatures.

When the Bose gas is compressed isothermically, the temperature remains constant but the volume decreases. As the particles are brought closer together, their interactions become stronger and can lead to the formation of a BEC. This is a phase transition where a large number of particles occupy the lowest energy state, resulting in a sudden decrease in entropy.

In this scenario, the work done on the system would be different compared to an ideal gas because the energy required to form a BEC must also be considered. This can be calculated using the Gibbs free energy, which takes into account both the energy and entropy changes in the system. The work done on the system would therefore be equal to the change in Gibbs free energy, given by the formula W = ΔG = ΔU - TΔS, where ΔU is the change in internal energy and ΔS is the change in entropy.

In summary, the work done on a Bose gas in an isentropic compression with subcritical temperature T < T_c would be different from an ideal gas due to the formation of a BEC. The calculation of work would involve considering the change in Gibbs free energy, which takes into account the energy and entropy changes in the system.
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top