Law of conservation of energy help

AI Thread Summary
The discussion focuses on applying the law of conservation of energy to determine the initial speed of a pen sliding across a desk. The pen, with a mass of 0.057 kg, experiences kinetic friction and slows down over a distance of 25 cm. The user calculates the work done by friction and the change in kinetic energy, ultimately finding the initial speed to be 1.1 m/s. Feedback confirms that the steps taken are correct, including unit conversions. The conversation emphasizes the importance of correctly applying energy conservation principles in physics problems.
jbjohnybaker
Messages
19
Reaction score
0

Homework Statement



A pen of mass 0.057 kg slides across a horizontal desk. In sliding 25 cm, its speed decreases to 5.7 cm/s. The force of kinetic friction exerted on the pen by the desk has a magnitude of 0.15N. Apply the law of conservation of energy to determine the initial speed of the pen.

Homework Equations


Eth = Fk deltaD
deltaEk = 1/2mv^2f - 1/2 mv^2i
Eth = delta Ek

The Attempt at a Solution



Eth = (.15)(0.25)
= 0.0375 J

DeltaEk = 1/2(0.057)(0.057) - 1/2(0.057)Vi^2
= 9.25965x10^-5 - 0.0285 Vi^2

Eth = DeltaEk
0.0375 J = 9.25965x10^-5 - 0.0285 Vi^2

Vi = sqrt ((0.0375 - 9.25965x10^9)/0.0285)
Vi = 1.1 m/s

I get the right answer but i am not sure if i used the right steps.. can you please check my steps.. thx
 
Physics news on Phys.org


The notation is different than I am used to, but it looks like all the steps are correct, even the unit conversions. (Which is normally the part that people miss)

Good job!
 


okay.. thank you
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top