Magnetic Field Help - Physics Problem Solutions

AI Thread Summary
The discussion revolves around solving three physics problems related to magnetic fields and forces on charged particles. For the first problem, participants suggest calculating the electric field between charged plates to determine the necessary magnetic field direction that would allow an electron to pass without deflection. In the second problem, the right-hand rule is emphasized to find the radius and pitch of an electron's spiral trajectory in a magnetic field, with specific equations provided for calculation. The third problem involves determining the current through two springs affected by a magnetic field, where participants discuss potential errors in calculations and the need for additional information about the springs. Overall, the thread highlights common challenges in applying physics concepts to solve problems involving magnetic fields and forces.
Camronnba
Messages
5
Reaction score
0
Magnetic Field Help

--------------------------------------------------------------------------------

Hi, when it comes to physics, I am the stupidiest person on Earth. Thus I have three questions, if someone could walk me through them I would be so thankful it would be ridiculous.

Problem 1.
An electron travels with speed 1.0 x 10^7 m/s between two parallel charged plates. The plates are separated by 1.0 cm and are charged by a 200 V battery. What magnetic field strength and direction will allow the electron to pass between the plates without being deflected?
(for this one I thought that if electrons travel parallel or antiparallel to a magnetic field it will always allow the electron to move. Like I said before I'm a physics idiot)

Problem 2.
The uniform 30 mT fiel points in the positive z direction. An electron enter the region of magnetic field with a speed 5.0 x 10^6 m/s and at an angle of 30 degrees above the xy plane. Find the radius r and the pitch p of the electron's spiral trajectory.
(I have no clue on this one)

Problem 3.
Two springs each have a spring constant of 10 N/m. They are stretched 1.0 cm when a current passes throught the wire. How big is the current?
Note: Magnetic field is 0.5 T, and length of wire is 20cm
(for this one, I found the magnitude of the spring force, multiplied that by 2 since there are two springs. I then set that equal to the F(magnetic field) which is defined by ILB. I then isolated to solve for I. I get an answer of 20A, but my textbook gives an answer of 2.0A. This would lead me to believe my error is small, or that the answer in the book is wrong)

Whowever can help me with these I would be very appreciative, thanks for your time!
 
Last edited:
Physics news on Phys.org
prob.0: you'll get better help from forum regulars with a "positive" attitude than with a "pity me" plea.

prob.1: see in your diagram that there's an E-field in the gap, pointing
from the +Q on one plate to the -Q on the other plate. Compute this E-field.
Which way would this E-field deflect an electron?
Which way should you arrange the B-field to point, in the gap, so that
the magnetic Force cancels the Electric Force?

prob.2: You DO know the right-hand rule, right? Circular motion (mv^2/r)?

prob.3: how many turns of spring are there?
 
p3. That information is not given, and I didn't think it was relevant because it is not a solenoid question?

and as far as the right hand rule goes, I have heard it but I am unsure of how it truly works.
 
point your right hand (fingers together, straight) in the direction of qv .
these are electrons, so qv is OPPOSITE their velocity
(qv is in the direction of the Indicated current ...)

Sweep your fingers only (keeping hand in place) to point in direction of local B.
You usually have to rotate your wrist around the qv axis to do this.
Fingers sweep through the angle "theta" in F = qv x B = qvB sin(theta).

Thumb sticks out perpendicuklar to hand and fingers, points in direction of F.

The springs themselves are carrying the current?
adjacent coils ATTRACT one another, so it should SHORTEN.
My guess was that there must be an external B-field, pushing on EACH coil.
 
What I did for problem 1, was use E=V/d to calculate the electic field. I then set that equal to qvB. When I solve for B I get an answer that is way too large. I think my mistake is in using E as F. What other calculations need to be done here?
 
For Problem 2, just use the equation:

r= \frac{m*v}{q*B}

except that we just want the velocity perpendicular to the B-field, so we use the equation:

r= \frac{m*v*cos(\pi/6)}{q*B}

Not sure how to find the pitch though. I'm thinking maybe something like:
p = r*tan(pi/6)

If you can figure out the second part, please post.

Graham
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top