Making a homemade electric lighter

  • Thread starter Thread starter theonecalledU
  • Start date Start date
  • Tags Tags
    Electric Homemade
AI Thread Summary
Nichrome is a suitable material for the heating element in a homemade electric lighter due to its high resistance and ability to withstand high temperatures. A wire length of 1.5-2 inches is recommended, with finer gauge wire for optimal heating efficiency. To maintain a constant temperature of at least 500°F, a temperature control circuit is necessary, potentially using a PWM (Pulse Width Modulation) controller for power regulation. Rechargeable batteries are advised for efficiency, with options like 4xAAA or 3AA being viable. Proper insulation and high-temperature soldering techniques are crucial for safely assembling the device.
theonecalledU
Messages
5
Reaction score
0
I'm trying to make an electric lighter ( like this http://imgur.com/a/wg8q7) using the framework of this guide.
http://www.instructables.com/id/Make-a-battery-powered-soldering-iron/?ALLSTEPS
except mine will have a few more feature and the soldering tip will be replaced with nichrome most likely.

Theres is just a few things that I am stuck on

-First, Is nichrome the best material to use as the heating element?
Assuming we do use a wire heating element the length of the wire will be 1.5-2 inches long, what would be the best gauge? any other details about it?

-Second, I need the heating element to stay at a constant temp of at least 500 Fahrenheit
What type of circuitry would I need to accomplish this, what if i wanted to to be able to control the amount of power?

-Third, what would be the best batteries to use for this? I was hoping to be able to use 4xAAA or 3AA
 
Last edited:
Engineering news on Phys.org
What are you intending to light with the device?
 
cigarettes and pipes
 
PF has a very strong policy on dangerous activities. Smoking tobacco is addictive and very dangerous. It will probably kill you.

Now after that caveat, back on the engineering subject of an electrical igniter.

The use of batteries to produce such heat would be very inefficient and so you would need to use rechargeable batteries.

You could get some fine nichrome wire from something like an old hair drier. You will only need a short length, maybe only about 1% of the length used in the drier. See what wire you can find and do some experiments.

Nichrome heater wire is a bit like stainless steel. It will be a challenge to attach it to terminals and hold the hot wire in place. You will need to back the heater coil with a good thermal insulator.
 
Electric jug element wire is very easy to solder to, if you can still get it. Toaster element wire is very difficult to solder to. In any case, the heated wire is likely to melt the solder. Perhaps a high temp solder might be a proposition?
 
How to Make an Electric Hot Wire Lighter :
 

Thread 'Query on Isentropic relationships (such as PV^gamma = constant)'

Hi all, I have a question. So from the derivation of the Isentropic process relationship PV^gamma = constant, there is a step dW = PdV, which can only be said for quasi-equilibrium (or reversible) processes. As such I believe PV^gamma = constant (and the family of equations) should not be applicable to just adiabatic processes? Ie, it should be applicable only for adiabatic + reversible = isentropic processes? However, I've seen couple of online notes/books, and...
View full post »
Thread 'How can I find the cleanout for my building drain?'

Thread 'How can I find the cleanout for my building drain?'

I am a long distance truck driver, but I recently completed a plumbing program with Stratford Career Institute. In the chapter of my textbook Repairing DWV Systems, the author says that if there is a clog in the building drain, one can clear out the clog by using a snake augur or maybe some other type of tool into the cleanout for the building drain. The author said that the cleanout for the building drain is usually near the stack. I live in a duplex townhouse. Just out of curiosity, I...
View full post »

Thread 'Dry sump pump issue'

I have an engine that uses a dry sump oiling system. The oil collection pan has three AN fittings to use for scavenging. Two of the fittings are approximately on the same level, the third is about 1/2 to 3/4 inch higher than the other two. The system ran for years with no problem using a three stage pump (one pressure and two scavenge stages). The two scavenge stages were connected at times to any two of the three AN fittings on the tank. Recently I tried an upgrade to a four stage pump...
View full post »

Similar threads

Designing a homemade electric lighter
Replies
6
Views
3K
Low voltage Low heat, battery powered heater
Replies
8
Views
3K
Static Electricity- Solving Material Placement Issues
Replies
4
Views
2K
I have a few questions about refrigeration and AC units
Replies
1
Views
3K
I Is the Poynting Vector Field the Only Factor in Energy Flow in Circuits?
Replies
16
Views
3K
Nichrome Wire foam cutter/heater
Replies
8
Views
6K
Noticed something in a clockwatch
Replies
12
Views
1K
Fire Starting Stick for Prairie Burns
Replies
5
Views
2K
Can IR Heating Be Effectively Focused Over Long Distances for Snow Prevention?
Replies
18
Views
3K
B Heat Pumps And The Peltier Effect
Replies
6
Views
2K

Hot Threads

Recent Insights

Back
Top