More Thoughts on lift generation

AI Thread Summary
The discussion centers on the mechanics of lift generation and the behavior of airflow around a wing. It argues against the notion that momentum transferred to the air by a wing will reach the ground, emphasizing that fluid forces on objects are limited to normal and tangential forces. The conversation highlights how, in 2D potential flow, the mechanical energy remains constant, and any downwash created by the wing does not result in energy transfer to the fluid that would cause drag. In 3D potential flow, however, wingtip vortices do impart energy to the fluid, leading to drag, which is a departure from D'Alembert's Paradox. Ultimately, the discussion concludes that while momentum may not reach the ground intact, it is dissipated through interactions at various scales.
Michael1160
Messages
16
Reaction score
0
I recently read an article where the author stated that the momentum transferred to the air by a passing wing will eventually strike the earth, even from a high cruise altitude (in other words, out of ground effect)

I have a problem with this for the following reasons, feedback would be appreciated.

There is only two ways that a fluid can impose forces on an object immersed in it:

1) Normal Forces (Pressure)
2) Tangential Forces (Friction)

From the standpoint of 2D potential flow:
Let's say we have a fluid element floating above a point on the earth. Relative to that point on the earth, the total pressure is just the static pressure of the air, made up of the density and the translational (internal) kinetic energy of the molecules.

However, approaching the fluid element from the right (the direction really does not matter) is an airplane with an airspeed of 100 Knots. Now, relative to that airplane the fluid element has a total pressure of static pressure + dynamic pressure. So, even before the airplane makes contact with the fluid element, it has effectively already done "work" on it, as the total pressure relative to the airplane has increased.

When the fluid element comes into the flow field of the wing (does not have to contact the wing, can be some distance (finite) above or below) it will go thru various velocity and "static" pressure changes. But, the mechanical energy of the flow remains constant, all accelerating and decelerating come about as a result of "internal" forces (no external forces increase or decrease the total mechanical energy- we are talking 2D potential flow).

After the wing leaves, and the fluid element exits the flow field, it will have to readjust to the freestream static pressure and direction. The fluid element will have been displaced from its initial position, downward (down wash) but it caint keep traveling in the downward direction after it leaves the flow field of the wing, as this would represent a transfer of energy to the fluid, which would mean the energy came from the airplane, which means the airplane would expierence a "drag" which 2D potential theory (D'Alembert's Paradox) says does not exist.

Now in 3D potential flow, energy will be imparted to the fluid (even without friction) as the wings will be a finite length, and the resluting wing tip vortices will repesent a transfer of energy to the fluid, which will be felt by the airplane as a drag force. These wingtip vortices distort the pressure distribution around the wing so that the pressure forces in the drag direction no longer cancel (D'Alembert's Paradox no longer valid).

Now, in real life the vortices will eventually be dissipated due to viscosity. I can see sound waves, which are weak pressure waves reaching the ground, but sound waves are not a mass movement of air.

feedback would be appreciated
 
Last edited:
Engineering news on Phys.org
I always forget to include something

From Newtons third law, the bending of the streamlines back up to the freestream direction and velocity, should reduce the lift slightly...and it does. This can be seen from a pressure distribution stand point also. As long as the fluid (streamlines) don't return to there original start position (there has to be a down wash) there will still be a positive lift.

In potential flow, there will be a stagnantion point at the trailing edge of the airfoil. However, on the last 10% to 15% of the airfoil, on the top surface, there will be a positive pressure (higher than freestream). This positive pressure on an aft facing surface will decrease the drag, but will also decrease the lift slightly, so this holds from a pressure distribution standpoint and Newton's 3rd law standpoint.

In addition, it usually takes 2 or 3 chord lengths past the trailing edge for the flow to return to the freestream static pressure and direction.

(yes, I know in potential flow without friction, how is the stagnation point going to move to the rear, however, remember potential flow and D'Alembert's Paradox are mathematical solutions.)
 
Last edited:
I re-read the article a few more times. I think the author is talking about a momentum flow reaching the earth...now this makes more sense.
 
Due to the inertia of air/vapor molecules and their elastic structure, I think the momentum would be dissapated and absorbed before reaching Earth ffom say several miles high. Most of the momentum would be conserved as angular momentum in the constiuent air particles.

Just my humble opinion, if you please.
 
Well, you really cain't dissipate momentum (you can dissipate energy)

However, if you are talking about the collision of two molecules with different masses, then I may see your point. However, wouldn't that just slow down the momentum flow?

Of course, if you were to have a glancing collision I can see where some of the momentum may be conserved as angular momentum ( in diatomic molecules at least)
 
Posted June 2024 - 15 years after starting this class. I have learned a whole lot. To get to the short course on making your stock car, late model, hobby stock E-mod handle, look at the index below. Read all posts on Roll Center, Jacking effect and Why does car drive straight to the wall when I gas it? Also read You really have two race cars. This will cover 90% of problems you have. Simply put, the car pushes going in and is loose coming out. You do not have enuff downforce on the right...
Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'
Scenario 1 (figure 1) A continuous loop of elastic material is stretched around two metal bars. The top bar is attached to a load cell that reads force. The lower bar can be moved downwards to stretch the elastic material. The lower bar is moved downwards until the two bars are 1190mm apart, stretching the elastic material. The bars are 5mm thick, so the total internal loop length is 1200mm (1190mm + 5mm + 5mm). At this level of stretch, the load cell reads 45N tensile force. Key numbers...
I'm trying to decide what size and type of galvanized steel I need for 2 cantilever extensions. The cantilever is 5 ft. The space between the two cantilever arms is a 17 ft Gap the center 7 ft of the 17 ft Gap we'll need to Bear approximately 17,000 lb spread evenly from the front of the cantilever to the back of the cantilever over 5 ft. I will put support beams across these cantilever arms to support the load evenly
Back
Top