Net force on ball from ground to top

AI Thread Summary
The discussion focuses on the net force acting on a ball tossed into the air during various stages of its flight. At the moment of release, the net force is upward but decreases as the ball ascends. At the highest point, the net force is not zero; gravity continuously acts downward, causing the ball to decelerate before reversing direction. As the ball descends, the net force is downward and increases due to gravitational pull. The key takeaway is that throughout the ball's trajectory, the net force is consistently the force of gravity acting downwards, influencing its motion.
mocking
Messages
3
Reaction score
0

Homework Statement


A ball is tossed up into the air. It reaches maximum height and comes back down.

What is the net force on the ball at the following situations:

a. The ball is moving upward as it is released.

b. The ball is at it's highest point. (when it comes to a stop i suppose)

c. The ball is moving downward.


Homework Equations



F = ma ?

The Attempt at a Solution



a. Force is up and decreasing.

b. Force is 0

c. Force is down and increasing.


Please let me know what you guys think. I have other problems also.
 
Physics news on Phys.org
Welcome to the Forum.a is correct before release. b is wrong. Think again.
What is making the ball slow down and then come back down ?

C is formally correct but in practical terms, not so.
 
Last edited:
At all points the net force on the ball is the force of gravity i.e. its weight acting downwards (ignoring air friction). Because of this force only, the ball first decelerates coming to rest at the top most point and then accelerates downwards.
 
Vijay just gave you the answer, so I'll see if I can help you understand it:

Let's suppose that at the very peak of it's flight, the force was equal to zero, as you initially thought. You also said the relevant equation is F=ma. Well, if F is zero, then the acceleration would also be zero. We already know that the velocity at that peak is zero. If the acceleration was also zero, then it'd just sort of stay there.
 
thank you for all your help! Mentz was wrong @ first but thank you for clearing up the rest.
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top