Optimum Angle for Sharp Edged Orifice Flow Pattern

AI Thread Summary
The angle of a sharp edged orifice significantly influences the flow pattern, with 30 and 45 degrees often recommended for optimal results. These angles may minimize vorticity, although the exact impact can vary based on the specific study objectives. Vortex generation is inevitable regardless of the angle chosen. The discussion highlights the importance of aligning the angle with the intended outcomes of the research. Understanding the flow dynamics through orifices is crucial for effective study design.
derekteo0710
Messages
6
Reaction score
0
How will the angle of the sharp edged orifice affect the flow pattern. Most of the angle is encourage to keep at 30 or 45 degree.

For a study vortex generation by pushing the water through a sharp edged orifice, what is the optimum angle I should adopt or what consideration should be made?

Thank you so much for your kind reply
 
Engineering news on Phys.org
What do you mean by a sharp edged orifice? I don't quite follow you here.
 
Sorry if I had gave an inappropriate term. I've attached a diagram to illustrate.
 

Attachments

  • 22092010246.jpg
    22092010246.jpg
    21.1 KB · Views: 438
Ah, I see what you mean now. It is hard to say exactly what angle is best, as that depends on what you intend to look for in your study. Suffice it to say that no matter what you do, there will be vortices generated. The 30 and 45 degree angles are most likely just special cases where the vorticity is minimum or something, though I am not 100% sure on that point as I have never done a study of the flow through an orifice myself.
 

Thread 'Race car suspension Class'

Posted June 2024 - 15 years after starting this class. I have learned a whole lot. To get to the short course on making your stock car, late model, hobby stock E-mod handle, look at the index below. Read all posts on Roll Center, Jacking effect and Why does car drive straight to the wall when I gas it? Also read You really have two race cars. This will cover 90% of problems you have. Simply put, the car pushes going in and is loose coming out. You do not have enuff downforce on the right...
View full post »
Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Scenario 1 (figure 1) A continuous loop of elastic material is stretched around two metal bars. The top bar is attached to a load cell that reads force. The lower bar can be moved downwards to stretch the elastic material. The lower bar is moved downwards until the two bars are 1190mm apart, stretching the elastic material. The bars are 5mm thick, so the total internal loop length is 1200mm (1190mm + 5mm + 5mm). At this level of stretch, the load cell reads 45N tensile force. Key numbers...
View full post »

Thread 'Cantilever help'

I'm trying to decide what size and type of galvanized steel I need for 2 cantilever extensions. The cantilever is 5 ft. The space between the two cantilever arms is a 17 ft Gap the center 7 ft of the 17 ft Gap we'll need to Bear approximately 17,000 lb spread evenly from the front of the cantilever to the back of the cantilever over 5 ft. I will put support beams across these cantilever arms to support the load evenly
View full post »

Similar threads

Water vs. water/glycol flow rates
Replies
1
Views
4K
Air Friction energy loss on a trampoline
Replies
13
Views
2K
Flow rate measurement: Venturi vs Sharp edged circular orifice. Help
Replies
1
Views
6K
Does Pipe Size Reduction Affect Flow Rate and Pressure Drop Significantly?
Replies
1
Views
3K
B Stability of Droplet Climbing on a Needle with Varying Contact Angle
Replies
2
Views
2K
How to Design an Orifice Plate for a Water Treatment Pilot Plant?
Replies
1
Views
51K
Why Do the Last Two Sprinklers Have a Smaller Spray Pattern?
Replies
8
Views
5K
Optimum mounting angle for three LEDs in a 240V LED light bulb
Replies
17
Views
2K
Flow of Water into a Bowl with Holes
Replies
6
Views
3K
Surface roughness in 2D sinusoidal corrugation
Replies
1
Views
4K

Hot Threads

Recent Insights

Back
Top