Reverse Current for RC Car Model: 3 Way Switch or Alternative Solution?

  • Thread starter Thread starter johnabbott123
  • Start date Start date
  • Tags Tags
    Switch
AI Thread Summary
To reverse the current in an RC car model without a speed controller, a three-way switch is a potential solution, but its effectiveness is uncertain. Reversing the current through the motor will enable the car to move in reverse, but this can complicate the circuit. Changing gears may be necessary to prevent unwanted backward movement. The discussion highlights the complexity of RC car circuits and the need for clarity on the specific problem being addressed. Exploring alternative methods for current reversal could yield additional insights.
johnabbott123
Messages
1
Reaction score
0
For a rc car model, is there any way to reverse the current like a speed controller would but without one to be able to make the car reverse?
I have been contemplating the option of three way switch but I'm not sure if it'll work. Any other helpful ideas?
 
Last edited:
Engineering news on Phys.org
Welcome to PF;
I'm sorry, you want to reverse the current through what exactly? RC Cars can have quite complicated circuits with current reversing and changing direction all over the place.

If you reverse the current through the motor, for eg, the motor will go in reverse.
The only way to stop this from making the car go backwards is to change gears.

What is the problem you are trying to solve?
 

Thread '3-terminal device external modeling'

Very basic question. Consider a 3-terminal device with terminals say A,B,C. Kirchhoff Current Law (KCL) and Kirchhoff Voltage Law (KVL) establish two relationships between the 3 currents entering the terminals and the 3 terminal's voltage pairs respectively. So we have 2 equations in 6 unknowns. To proceed further we need two more (independent) equations in order to solve the circuit the 3-terminal device is connected to (basically one treats such a device as an unbalanced two-port...
View full post »

Thread 'Question about the voltage between two charged capacitors'

suppose you have two capacitors with a 0.1 Farad value and 12 VDC rating. label these as A and B. label the terminals of each as 1 and 2. you also have a voltmeter with a 40 volt linear range for DC. you also have a 9 volt DC power supply fed by mains. you charge each capacitor to 9 volts with terminal 1 being - (negative) and terminal 2 being + (positive). you connect the voltmeter to terminal A2 and to terminal B1. does it read any voltage? can - of one capacitor discharge + of the...
View full post »
Thread 'Weird near-field phenomenon I get in my EM simulation'

Thread 'Weird near-field phenomenon I get in my EM simulation'

I recently made a basic simulation of wire antennas and I am not sure if the near field in my simulation is modeled correctly. One of the things that worry me is the fact that sometimes I see in my simulation "movements" in the near field that seems to be faster than the speed of wave propagation I defined (the speed of light in the simulation). Specifically I see "nodes" of low amplitude in the E field that are quickly "emitted" from the antenna and then slow down as they approach the far...
View full post »

Similar threads

Bidirectional current switching with single type transistor
Replies
42
Views
4K
12V DC Motor in Light Fixture with Dimmer & 12V DC to 110V AC Inverter
Replies
21
Views
2K
Switching between parallel and series connections (solar)
Replies
31
Views
4K
Linear moving switch, decade counter, chaser
Replies
49
Views
4K
Computer Science Student Seeks Advice on Switches & Junctions
Replies
9
Views
2K
How can I reroute multiple signals from a 4 pin connector using a relay switch?
Replies
37
Views
6K
Motorcycle starter safety circuit
Replies
11
Views
4K
High-Power Switching using MOSFETs
Replies
14
Views
4K
Programmable polarity reversal circuit
Replies
2
Views
2K
How can I safely energize a suspect alternator
Replies
16
Views
3K

Hot Threads

Recent Insights

Back
Top