Solving the Relativity Question: When Does Mission Control Receive Confirmation?

  • Thread starter Thread starter andytran
  • Start date Start date
  • Tags Tags
    Relativity
AI Thread Summary
The discussion centers on calculating the timing of communication between an explorer traveling at 0.9c and mission control. To determine when mission control receives the first confirmation signal, the Lorentz transformation is essential for calculating time and location in the rest frame. The same transformation helps establish when the explorer receives the first status report. Participants suggest using distance calculations based on light speed to find the timing of these signals. The conversation emphasizes the importance of relativity formulas in solving these communication timing questions.
andytran
Messages
41
Reaction score
0
hey


here is the question,

suppose an explorer set out on a ship traveling to some stars at a constant velocity of 0.9c. every week mission controller and explorer each transmit status report to each other and acknowledge receipt by transmitting a confirmation signal back

when does mission control receive the first confirmation signal?

when does the explorer receive the first status report?

any suggestions are welcomed!.
thx
 
Physics news on Phys.org
Using your relativity formulas, figure out how far the explorer has gone after one week. Then divide that distance by 186,000 and you'll get how many seconds it takes the message to reach the planet. The reverse trip... I'm not so sure on. If I weren't so focused on other areas of physics atm, I'd be able to help more. Hope I helped some though?
 
andytran said:
hey


here is the question,

suppose an explorer set out on a ship traveling to some stars at a constant velocity of 0.9c. every week mission controller and explorer each transmit status report to each other and acknowledge receipt by transmitting a confirmation signal back

when does mission control receive the first confirmation signal?

when does the explorer receive the first status report?

any suggestions are welcomed!.
thx
You have to use the Lorentz transformation to determine the time (t) and location (x) in the mission controller (rest) frame when the confirmation signal is sent. Then, using t = x/c determine when in the rest frame the signal is received and confirmation sent. You then use the reverse Lorentz transformation to determine that time as measured in the explorer's (moving) frame and the explorer's position at that time (relative to the controller but measured in the moving frame). Then, using t'=x'/c you can determine what time it will be received by the explorer.

AM
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top