Supposedly Simple, 1-D Motion Question

  • Thread starter Thread starter Luca169
  • Start date Start date
  • Tags Tags
    Motion
AI Thread Summary
A driver traveling at 56.0 km/h must react to a boy 65 m ahead by applying brakes that decelerate at 3.00 m/s². The initial approach using the equation Δd = V1Δt + 1/2a(Δt)² was deemed inappropriate due to non-constant acceleration. The quadratic formula was attempted but yielded negative values, indicating an error in calculations. A revised method calculated the stopping time and distance, concluding that the driver has approximately 1.58 seconds to react to avoid a collision. The procedure appears correct, with minor discrepancies in the final answer.
Luca169
Messages
7
Reaction score
0

Homework Statement


A man is driving at 56.0 km/h [N]. Suddenly, a boy stumbles on the road 65 m ahead of the car. After t seconds the driver finally decides to hit the brakes, which then produces an acceleration of 3.00 m/s² . What is the maximum reaction time allowed if the driver is to avoid hitting this student?

Homework Equations


I started off trying to use Δd = V1Δt + 1/2a(Δt)² , however I was told this won't work since acceleration is not constant, this I understand. Then, I tried using quadratic formula to solve, but for me it wouldn't work since the number I was trying to find the square root of was negative.

The Attempt at a Solution


I would write the steps I took during my quadratic formula phase, but I'm not sure I even did it correctly, any help with this would be appreciated.
 
Physics news on Phys.org
Luca169 said:

Homework Statement


A man is driving at 56.0 km/h [N]. Suddenly, a boy stumbles on the road 65 m ahead of the car. After t seconds the driver finally decides to hit the brakes, which then produces an acceleration of 3.00 m/s² . What is the maximum reaction time allowed if the driver is to avoid hitting this student?

Homework Equations


I started off trying to use Δd = V1Δt + 1/2a(Δt)² , however I was told this won't work since acceleration is not constant, this I understand. Then, I tried using quadratic formula to solve, but for me it wouldn't work since the number I was trying to find the square root of was negative.

The Attempt at a Solution


I would write the steps I took during my quadratic formula phase, but I'm not sure I even did it correctly, any help with this would be appreciated.


Just write out your quadratic. You don't need to show the intermediate steps.
 
0 = (-1.5m/s²)(Δt)² + (16m/s)(Δt) - 65m
X1= 5.3 X2 = 5.3

That's not the answer I'm supposed to be getting.. What have I done wrong?
 
Luca169 said:
0 = (-1.5m/s²)(Δt)² + (16m/s)(Δt) - 65m
X1= 5.3 X2 = 5.3

That's not the answer I'm supposed to be getting.. What have I done wrong?

OK I get 15.55m/s instead of 16 for your equation.

But perhaps a different approach might be easier?

How long does it take to slow from 15.55m/s to 0 at -3m/s2? That's your time budget to stop.

Using that time, determine how much distance you require to stop.

If it is less than 65m then then how long can you continue at 15.55m/s before you have to stop?

If it is longer than 65m, start calling 9-1-1.
 
0 m/s = 15.55 m/s + (-3.00m/s²)(Δt)
-15.55m/s/-3.00m/s=(Δt)
(Δt)=5.183
Δd=15.55m/s(5.183s)+1/2(-3.00m/s²)(5.183s)²
Δd=40.3m
65m - 40.3m = 24.7m/15.55m/s= 1.58 s?

This is about two decimal places off from the given answer (1.56) however, is the procedure correct?
 
Thread 'Voltmeter readings for this circuit with switches'
TL;DR Summary: I would like to know the voltmeter readings on the two resistors separately in the picture in the following cases , When one of the keys is closed When both of them are opened (Knowing that the battery has negligible internal resistance) My thoughts for the first case , one of them must be 12 volt while the other is 0 The second case we'll I think both voltmeter readings should be 12 volt since they are both parallel to the battery and they involve the key within what the...
Thread 'Struggling to make relation between elastic force and height'
Hello guys this is what I tried so far. I used the UTS to calculate the force it needs when the rope tears. My idea was to make a relationship/ function that would give me the force depending on height. Yeah i couldnt find a way to solve it. I also thought about how I could use hooks law (how it was given to me in my script) with the thought of instead of having two part of a rope id have one singular rope from the middle to the top where I could find the difference in height. But the...
Back
Top