Troubleshooting Electromagnet Design for Telegraph Key and Sounder

  • Thread starter Thread starter Cspeed
  • Start date Start date
  • Tags Tags
    Electromagnet
AI Thread Summary
The discussion focuses on troubleshooting a telegraph key and sounder design that utilizes a ferromagnetic nail as an electromagnet. The creator is struggling to generate sufficient magnetic attraction with their current setup, using either AA or D batteries, and is not achieving the desired sound effect. Suggestions include increasing the number of wire turns on the nail, using a higher voltage power source, and considering alternative ferromagnetic materials like screws for better performance. The importance of using appropriate magnet wire and ensuring a good magnetic circuit is emphasized, with a recommendation to explore a horseshoe magnet design for improved results. Implementing these changes is expected to enhance the functionality of the telegraph sounder.
Cspeed
Messages
44
Reaction score
0
I'm trying to build a telegraph key and sounder. The sounder that I have designed (well, saw online) is a metal nail (which is ferromagnetic) with at least several dozen (maybe 200+) turns of wire around it. When a current is on the wire, the nail should become an electromagnet, and then pull down some kind of ferromagnetic metal strip, creating a sound. Upon being released, the strip bounces back up (maybe using a rubber band) to clang against something else.

My issue: Using either two AA batteries or two D batteries, I can't get the nail to attract much of anything, not even close to making a sound. I haven't found a good metal strip yet, but even paper clips barely get attracted to the nail. If a compass is close enough, it will detect the magnetic field. Any suggestions? Is it possible that the nail isn't very ferromagnetic, or is there something better to use? Thanks for any help.
 
Engineering news on Phys.org
You need either more turns or more current. Try a 6V lantern battery or a 12 V Pb-acid alarm battery.
 
You might increase the diameter of your core. Try a screw, for example, maybe 1/4-20 x 2", wrapped with 1 layer of electrical tape so the threads don't bite into the wire. Are you using small gauge (around 24 AWG) magnet wire? (Magnet wire has a clear coating instead of thick plastic insulation, so you can wind many turns in a small radius.) Two dozen turns won't do the job--try hundreds. You should get action!
 
I probably have 100-200 turns of 28 AWG, insulated. Does the length of the nail matter? It's about 0.5 cm diameter, 6cm length.
 
Here is a nice telegraph sounder design:
http://www.sfu.ca/~achanne/projects/Telegraph%20Sounder/
There are two solenoid coils wound around small bolts, with a piece of iron connecting the bottoms of the two bolts, to create a horseshoe electromagnet. This horseshoe magnet design with two coils is a much better magnetic circuit than a single nail.
 
Last edited by a moderator:
Wow, that's a great guide. I'll go ahead and try that out then.
 
Posted June 2024 - 15 years after starting this class. I have learned a whole lot. To get to the short course on making your stock car, late model, hobby stock E-mod handle, look at the index below. Read all posts on Roll Center, Jacking effect and Why does car drive straight to the wall when I gas it? Also read You really have two race cars. This will cover 90% of problems you have. Simply put, the car pushes going in and is loose coming out. You do not have enuff downforce on the right...
I'm trying to decide what size and type of galvanized steel I need for 2 cantilever extensions. The cantilever is 5 ft. The space between the two cantilever arms is a 17 ft Gap the center 7 ft of the 17 ft Gap we'll need to Bear approximately 17,000 lb spread evenly from the front of the cantilever to the back of the cantilever over 5 ft. I will put support beams across these cantilever arms to support the load evenly
Thread 'What's the most likely cause for this carbon seal crack?'
We have a molded carbon graphite seal that is used in an inline axial piston, variable displacement hydraulic pump. One of our customers reported that, when using the “A” parts in the past, they only needed to replace them due to normal wear. However, after switching to our parts, the replacement cycle seems to be much shorter due to “broken” or “cracked” failures. This issue was identified after hydraulic fluid leakage was observed. According to their records, the same problem has occurred...

Similar threads

Back
Top