Tuned mass damper does not reduce the amplitude of vibration?

  • Thread starter Thread starter gunna
  • Start date Start date
  • Tags Tags
    Vibration
AI Thread Summary
A tuned mass damper (TMD) is designed to reduce vibrations at a specific frequency, typically tuned to the natural frequency of the primary system. In this case, the primary system has a natural frequency of 0.31 Hz and is excited at 0.6 Hz, which is causing an amplification in the response rather than a reduction. The discussion highlights that adding a TMD tuned to 0.6 Hz creates a two-degree-of-freedom system that does not effectively mitigate the response at that frequency. It is clarified that TMDs are most effective when tuned to the natural frequency of the primary system, not an external excitation frequency. Therefore, using a TMD in this scenario may not be appropriate for reducing the response at 0.6 Hz.
gunna
Messages
3
Reaction score
0
Hello everyone,

I have a simple question. Lets say a single degree of freedom system (SDOF) which consists of a spring and a mass is excited by an external force. The SDOF system has the eigenfrequency of 0.31 Hz and the external force is a periodic force with the frequency of 0.6 Hz. After decay of the transient effects, the frequency response function of the SDOF system should contain peaks at the system's eigenfrequency of 0.31 Hz and the 0.6 Hz excitation, right?

Now I want to reduce the response at 0.6 Hz induced by the excitation with a tuned mass damper (TMD). The TMD also consists of a spring and a mass, and the eigenfrequency of the TMD is tuned to 0.6 Hz, as it should reduce this frequency. I built this configuration in ANSYS and calculated the SDOFs response under the influence of the TMD and the system's response at 0.6 Hz is even getting bigger.

Am I understanding something wrong? Should a TMD with the tuned eigenfrequency not reduced the system's response at THAT frequency after the decay of the transient effects?

Another thought is the excitation induces resonance in the TMD and thus causing an amplification in the SDOF's system at the excitation frequency...

Best regards
 
Last edited by a moderator:
Engineering news on Phys.org
Welcome, @gunna !

Shouldn't the oscillation frequency of the TMD be tuned to be similar to the resonant frequency of the object it is mounted to (eigenfrequency of 0.31 Hz)?
 
gunna said:
I built this configuration in ANSYS and calculated the SDOFs response under the influence of the TMD and the system's response at 0.6 Hz is even getting bigger.
You have a system with resonant frequency of 0.31 Hz that is excited at 0.6 Hz. The response will be small because the magnitude of the response is determined by the mass of the system and the magnitude of the excitation. Then you added a second system with a resonant frequency of 0.6 Hz. That system is driven at its resonant frequency by the 0.6 Hz excitation, so the amplitude is large. Your system is a simple two DOF system with two distinct natural frequencies that is excited at one of those frequencies. Your two DOF system has no relation to a TMD. TMD theory does not apply to your system.

A TMD does two things:
1) It changes a lightly damped natural frequency to two lightly damped natural frequencies, one higher and the other lower than the original natural frequency. This is useful when there is excitation only at the original natural frequency.

2) Adding a damper to the tuned mass damps vibration of the primary mass at both of the new natural frequencies. This is useful when the excitation is over a range of frequencies.
 
Lnewqban said:
Welcome, @gunna !

Shouldn't the oscillation frequency of the TMD be tuned to be similar to the resonant frequency of the object it is mounted to (eigenfrequency of 0.31 Hz)?
I agree, usually the TMD is tuned to the eigenfrequency of the structure. But in my case I want to mitigate the response at 0.6 Hz, and a TMD should be able to reduce any frequency as long as it is tuned to that specific frequency right?

Best regards
 
jrmichler said:
You have a system with resonant frequency of 0.31 Hz that is excited at 0.6 Hz. The response will be small because the magnitude of the response is determined by the mass of the system and the magnitude of the excitation. Then you added a second system with a resonant frequency of 0.6 Hz. That system is driven at its resonant frequency by the 0.6 Hz excitation, so the amplitude is large. Your system is a simple two DOF system with two distinct natural frequencies that is excited at one of those frequencies. Your two DOF system has no relation to a TMD. TMD theory does not apply to your system.

A TMD does two things:
1) It changes a lightly damped natural frequency to two lightly damped natural frequencies, one higher and the other lower than the original natural frequency. This is useful when there is excitation only at the original natural frequency.

2) Adding a damper to the tuned mass damps vibration of the primary mass at both of the new natural frequencies. This is useful when the excitation is over a range of frequencies.
I can follow you by saying I just created a 2DOF system with two distinct natural frequencies that is excited at one of those frequencies. But that is what a TMD does, right? Turning a SDOF system into a 2DOF system and by doing so, reduce the SDOF system's response at it's natural frequency.
But since I am not interested at reducing the SDOF's response at it's natural frequency but rather at reducing the SDOF's response at another excitation frequency, the use of a tuned mass damper is not appropiated. Is that what both of you are trying to tell me?

Best regards
 
How did you find PF?: Via Google search Hi, I have a vessel I 3D printed to investigate single bubble rise. The vessel has a 4 mm gap separated by acrylic panels. This is essentially my viewing chamber where I can record the bubble motion. The vessel is open to atmosphere. The bubble generation mechanism is composed of a syringe pump and glass capillary tube (Internal Diameter of 0.45 mm). I connect a 1/4” air line hose from the syringe to the capillary The bubble is formed at the tip...
Thread 'What type of toilet do I have?'
I was enrolled in an online plumbing course at Stratford University. My plumbing textbook lists four types of residential toilets: 1# upflush toilets 2# pressure assisted toilets 3# gravity-fed, rim jet toilets and 4# gravity-fed, siphon-jet toilets. I know my toilet is not an upflush toilet because my toilet is not below the sewage line, and my toilet does not have a grinder and a pump next to it to propel waste upwards. I am about 99% sure that my toilet is not a pressure assisted...
After over 25 years of engineering, designing and analyzing bolted joints, I just learned this little fact. According to ASME B1.2, Gages and Gaging for Unified Inch Screw Threads: "The no-go gage should not pass over more than three complete turns when inserted into the internal thread of the product. " 3 turns seems like way to much. I have some really critical nuts that are of standard geometry (5/8"-11 UNC 3B) and have about 4.5 threads when you account for the chamfers on either...
Back
Top