Two independent driven inputs one output

AI Thread Summary
The discussion revolves around creating a mechanism that allows two independent inputs to drive a single output without influencing each other. The user seeks a compact and lightweight solution, exploring options like centrifugal clutches, freewheel mechanisms, and epicyclic gears but finds them inadequate for their needs. Suggestions include using a ratcheting system to allow one input to coast while the other provides power, or employing hydraulics to manage the inputs. Another proposed solution involves a splined sleeve that can slide between two input shafts or a sliding output gear to select the active input. The user expresses frustration over the complexity of the problem and seeks further assistance.
joshb93
Messages
2
Reaction score
0
Hello everyone,

I've been trying to figure out how i can have two different inputs that are switchable from one to another that drive a single output. However i don't want the inputs to drive each other, and also want the mechanism to be compact in size and fairly lightweight. So how can i do this?

INFO
I have one engine that is a high speed the other source is a hand/foot powered one. I have all ready researched about different types of clutch but this will be to bulky for the application, unless a centrifugal clutch was used but that still does not solve the problem of the handles/pedals rotating when the engine is working. I have also looked at a free wheel mechanism like you find on a push bike but still can't figure out how to get this to work how i want it to. Lastly i have looked at epicyclic/planetary gears but just can't understand how it work with two inputs leaving handles/pedals in a free motion.

To say the least i have slightly confused myself, perhaps I've been over thinking the problem and there is a simple answer, but its really bugging me now so i appreciate any help you can offer.

Thanks Josh,
 
Last edited:
Engineering news on Phys.org
Hi Averages, thanks for the reply that isn't exactly what i was looking for, its my fault i hadn't worded the question quite right, in simple terms i have two inputs i want these to stay separate and not power each other and then i want to be able to easily switch from one input to the other (only have one input on at a time).
 
You could have each input "ratchet" and coast when the other input is providing more power. Then only the greater power input would actually drive the system at any time.
 
Or could you drive through hydraulics - and each input would raise the hydraulic total power ?
 
One possibility would be to have the two splined input drive shafts end to end, with a splined sleeve output that can slide along the shaft onto one or the other to select drive to the output.

Similarly, sliding an output gear between two input gear wheels would select one input only.
 
I need some assistance with calculating hp requirements for moving a load. - The 4000lb load is resting on ball bearing rails so friction is effectively zero and will be covered by my added power contingencies. Load: 4000lbs Distance to travel: 10 meters. Time to Travel: 7.5 seconds Need to accelerate the load from a stop to a nominal speed then decelerate coming to a stop. My power delivery method will be a gearmotor driving a gear rack. - I suspect the pinion gear to be about 3-4in in...
Thread 'Turbocharging carbureted petrol 2 stroke engines'
Hi everyone, online I ve seen some images about 2 stroke carbureted turbo (motorcycle derivation engine). Now.. In the past in this forum some members spoke about turbocharging 2 stroke but not in sufficient detail. The intake and the exhaust are open at the same time and there are no valves like a 4 stroke. But if you search online you can find carbureted 2stroke turbo sled or the Am6 turbo. The question is: Is really possible turbocharge a 2 stroke carburated(NOT EFI)petrol engine and...
How did you find PF?: Via Google search Hi, I have a vessel I 3D printed to investigate single bubble rise. The vessel has a 4 mm gap separated by acrylic panels. This is essentially my viewing chamber where I can record the bubble motion. The vessel is open to atmosphere. The bubble generation mechanism is composed of a syringe pump and glass capillary tube (Internal Diameter of 0.45 mm). I connect a 1/4” air line hose from the syringe to the capillary The bubble is formed at the tip...
Back
Top