What are possible subtopics for a physics extended essay on firearms?

AI Thread Summary
The discussion centers on developing subtopics for an IB extended essay in physics focused on firearms. Two proposed subtopics include analyzing momentum laws related to recoil and terminal ballistics, and exploring gas laws concerning the firing process and sound reduction. A suggested experiment involves using a pendulum to measure the momentum of a bullet, although safety concerns are noted. Participants share personal experiences with similar experiments, emphasizing the potential for accurate results. The conversation also touches on the challenges of sourcing materials and the impact of importation laws on firearm accessories in Canada.
Vodka
Messages
15
Reaction score
0
i'm starting [again] a physics topic for extended essay for IB...my last few topics haven't worked due to technical difficulties [ie: can't complete experiments, lack of avaliable resources, etc] so my new idea for a topic is firearms. the lab can easily be done by going to a shooting range sometime this week.

i'm looking to have at least three comprehensive subthesis', each focusing on a field of physics that is directly relevant. my ideas for two so far are:

momentum laws - primary/secondary recoil, terminal ballistics etc, all with a few relevant equations.

gas laws - actual firing of gun, how it cycles, noise generated and how it could be reduced, might be able to get some relevant figures [ratio of gunpowder grain to gaseous products]

i don't know what to do the last one on..kinematics and sound could be plasuable if i need, but are both sortof weak. so any sortof help would be great. thanks :)
 
Physics news on Phys.org
vodka, I don't have enough knowledge/ideas about rifles to help
except to dig up from memory an experiment that
a Freshman physics (like 1A or 1B) did years ago in class (!) with a 22.

I guess it was after class had ended.

there was a wooden frame like a sawhorse from which was
suspended a pendulum
and the pendulum bob was a large block of wood of known mass into which the bullet would embed itself on impact

the 22 rifle, IIRC, was clamped in a vise on the experiment bench.

an observer from the side (far enough away for safety)
could see what angle the pendulum swung

the bullet mass was determined
it was fired into the pendulum, which was hanging at rest,

the momentum imparted to the combined mass of wood block and slug
was determined from the angle of swing

the speed of the slug was calculated

perhaps this is a standard procedure
(i mention it only because it is all I got that is remotely
applicable)

BTW this seems potentially dangerous to me because the suspension of the pendulum is critical and the slug must hit dead center to avoid putting a torque on the block.

I'm not recommending this! It is just all I've seen done with firearms in first year college physics.
 
Last edited:
I did a similar experiment, except with an airsoft gun. It was hard to get a correct angle reading, but once I did, i was surprised by the accuracy of the experiment. The gun shot 280 FPS according to the manufacturer. My experiment found the average velocity around 260-270 FPS. Not bad!
 
on a completely tangential point, what gun do you have? ^_^

i got a mk23 socom kit and a tm mp5a4hg. it currently has a navy flashhider, clawmount, guarder 11stage RDS, 2 and 3 pt slings, 2x hicaps, 5x locaps, an ICS triplerail handgrip, mag clamp, large 8.4 3000mah battery in a case. in the process of purchasing a vertical handgrip, and looking into a better flashlight and laser pointer. I've spent so much, its obscene.

i get to spend about twice what you would for the same thing because of the stoopid importation laws in Canada. ah well. least we get trademarks and unpainted barrels
 
Thread 'Collision of a bullet on a rod-string system: query'
In this question, I have a question. I am NOT trying to solve it, but it is just a conceptual question. Consider the point on the rod, which connects the string and the rod. My question: just before and after the collision, is ANGULAR momentum CONSERVED about this point? Lets call the point which connects the string and rod as P. Why am I asking this? : it is clear from the scenario that the point of concern, which connects the string and the rod, moves in a circular path due to the string...
Thread 'A cylinder connected to a hanged mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top