What Forces and Powers Are Involved in Moving a Wire Through a Magnetic Field?

  • Thread starter Thread starter cse63146
  • Start date Start date
  • Tags Tags
    Force Push Wire
AI Thread Summary
The discussion revolves around calculating the forces and power involved in moving a wire through a magnetic field. The pushing force is determined using the equation F_push = (v L^2 B^2) / R, yielding a value of 6.25 x 10^-4 N. The input power supplied to the wire is calculated as 3.125 x 10^4 W, with the induced current found to be 1.25 x 10^-2 A. There is confusion regarding the direction of the induced current, which is clarified using the right-hand rule, indicating it flows in a direction that opposes the change in magnetic flux. The thread highlights the importance of significant figures in calculations and seeks validation on the answers provided.
cse63146
Messages
435
Reaction score
0

Homework Statement



The 10-cm-wide, zero-resistance slide wire shown in the figure is pushed toward the 2.0\Omegaresistor at a steady speed of 0.50 m/s. The magnetic field strength is 0.50 T.

knight_Figure_33_44.jpg


A) How big is the pushing force?
B) How much power does the pushing force supply to the wire?
C) What is the magnitude of the induced current?
D) How much power is dissipated in the resistor?

Homework Equations



F_{push} = \frac{v L^2 B^2}{R}

P_{input} = F_{push}*v = \frac{v^2 L^2 B^2}{R}

The Attempt at a Solution



A) F_{push} = \frac{v L^2 B^2}{R} = \frac{(0.5) (0.1)^2 (0.5)^2}{2} = 6.25 * 10^{-4} N

B) P_{input} = F_{push}*v = \frac{v^2 L^2 B^2}{R} = \frac{(0.5)^2 (0.1)^2 (0.5)^2}{2} = 3.125 * 10^4 W

C) I = \frac{vLB}{R} = \frac{(0.5)((0.1)(0.5)}{2} = 1.25 * 10^2 A

D) P_{dissipated} = P_{input} = 3.125 * 10^4 W

Did I make any mistakes?
 
Last edited:
Physics news on Phys.org
I am working on exactly same one.

I used I=E/R=(vLB)/R equation to solve C, and had 0.0125A or 1.25*10^-2

but they said it's not quite. :-(

Anyway, there is another question: What is the direction of the induced current?

I know I need to use the right hand rule but can't apply it right.

Is it clockwise or counterclockwise? anyone can explain?
 
The induced current opposes the change in magnetic flux through the loop. As you push the bar to the right you are decreasing the amount of "out of the page" magnetic field so the loop creates a current that would result in MORE magnetic field "out of the page".

Put your hand in the "thumbs up" position and point your thumb in the direction of the magnetic field you want to create...right now, "out of the page". The direction your fingers curl is the direction of the induced current. (ie along your fingers towards your fingernails.
 
man, still confused with "out of the page"

but.. okay. somewhat got it...

Still, nobody for part C ?
 
dmsgo89, I'm pretty sure your answer for C is correct, or is at least the answer I got. Check your significant figures though.
 
TL;DR Summary: I came across this question from a Sri Lankan A-level textbook. Question - An ice cube with a length of 10 cm is immersed in water at 0 °C. An observer observes the ice cube from the water, and it seems to be 7.75 cm long. If the refractive index of water is 4/3, find the height of the ice cube immersed in the water. I could not understand how the apparent height of the ice cube in the water depends on the height of the ice cube immersed in the water. Does anyone have an...
Thread 'Variable mass system : water sprayed into a moving container'
Starting with the mass considerations #m(t)# is mass of water #M_{c}# mass of container and #M(t)# mass of total system $$M(t) = M_{C} + m(t)$$ $$\Rightarrow \frac{dM(t)}{dt} = \frac{dm(t)}{dt}$$ $$P_i = Mv + u \, dm$$ $$P_f = (M + dm)(v + dv)$$ $$\Delta P = M \, dv + (v - u) \, dm$$ $$F = \frac{dP}{dt} = M \frac{dv}{dt} + (v - u) \frac{dm}{dt}$$ $$F = u \frac{dm}{dt} = \rho A u^2$$ from conservation of momentum , the cannon recoils with the same force which it applies. $$\quad \frac{dm}{dt}...
Back
Top