What is the final charge on the capacitor in this circuit?

  • Thread starter Thread starter joshanders_84
  • Start date Start date
  • Tags Tags
    Capacitor Charging
AI Thread Summary
The discussion centers on calculating the final charge on a capacitor in a circuit with a switch and three resistors. The user has determined the currents through the resistors but struggles to find the final charge, initially using incorrect voltage values. It is clarified that the voltage across the capacitor differs from that across resistor 3 and that Kirchhoff's laws may be necessary for accurate calculations. The importance of consistent units and careful review of calculations is emphasized to avoid errors. Ultimately, the user is encouraged to break down the problem and seek further assistance if needed.
joshanders_84
Messages
23
Reaction score
0
So I have done most of this problem, but can't seem to find the final charge on that capacitor. It says that there was a switch, even though it is not in the image, and that at t=0 the switch is closed, and that the capictor had no charge initially. I solved for and know that I1 = 4.2 A, I2 = 1.4 A, and I3 = 2.8 A, where 1, 2, and 3 refer to the resistors with the same numbers. But I can't solve for the final charge on the capacitor! I know that Qf = EC, and the capacitance is 4 * 10^6, and that E = 42V, but (4*10^6)(42) wasn't right. So then I solved for the Voltage that goes through resistor 3 and got that it was 8.2V, but (4*10^6)(8.2) wasn't right either. I don't understand what the proper answer is, or how to obtain it. Your help is appreciated; thanks!
Josh
 

Attachments

  • charged_capacitor.jpg
    charged_capacitor.jpg
    8.5 KB · Views: 372
Physics news on Phys.org
If you're asking for the "final charge" on the capacitor then there should be no current flowing through the third resistor.
 


Based on the information provided, it seems like you have all the necessary values to solve for the final charge on the capacitor. It's possible that you made a calculation error or used the wrong units in your calculations. Make sure to double check your work and use consistent units throughout.

Also, keep in mind that the voltage across the capacitor will not be the same as the voltage across resistor 3. The voltage across the capacitor will depend on the total current flowing through the circuit, not just the current through resistor 3. So, you may need to use Kirchhoff's laws to calculate the total current and then use that in your calculation for the final charge on the capacitor.

If you're still having trouble, it might be helpful to break down the problem into smaller parts and solve for each component individually. This can help you identify any errors or misunderstandings in your calculations.

Overall, it's important to carefully review the problem and make sure you're using the correct equations and values to solve for the final charge on the capacitor. Don't hesitate to reach out for additional help if needed. Good luck!
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top