Hammer + Nail forces Will answer in response

  • Thread starter Thread starter sadakaa
  • Start date Start date
  • Tags Tags
    Forces Response
AI Thread Summary
The discussion revolves around calculating the downward force exerted by a hammer on a nail as it drives the nail into wood. The hammer's initial speed is 1.2 m/s, and it stops after driving the nail 0.95 cm into the wood. The weight of the hammer head is 6N, with an additional force of 14N applied by the user. Using Newton's laws, the acceleration of the hammer is determined to be approximately 75.79 m/s². The final equation incorporates the forces acting on the hammer, leading to the calculation of the total downward force exerted on the nail.
sadakaa
Messages
18
Reaction score
0
1. A hammer is pounding a nail straight down into a wooden board. Just before the hammer hits the nail, the speed of the hammer is 1.2 m/s. The hammer drives the nail into the wood and stops after the nail goes in a distance of 0.95 cm. The weight of the hammer head is 6N, and in addition to this weight there is a force of 14 N exerted on the hammer head by the person using the hammer. Assume that the acceleration of the hammerhead is constant while it is contact with the nail and moving downward, (i.e., while the hammer is slowing from its initial speed to zero). Calculate the magnitude of the downward force exerted by the hammer head on the nail while it is driving the nail into the wood. (Hint: By Newton’s third law, the force of the hammer head on the nail has equal magnitude to the force of the nail up on the hammer head. Ask yourself what are all the forces on the hammer head.)

Homework Equations



V2 = V02 + 2a(x-x0)

The Attempt at a Solution



Take up as positive, thus:

V0 = -1.2 m/s
V = 0
X0 = .0095 m
X = 0

0 = -1.22 +2(a)(-.0095)
a = 75.7895 m/s2

Now i get stuck. I set up the equation

ma = Fnormal - Fperson - Fgrav

I'm not too sure how to continue. Help!
 
Physics news on Phys.org
sadakaa said:
1. A hammer is pounding a nail straight down into a wooden board. Just before the hammer hits the nail, the speed of the hammer is 1.2 m/s. The hammer drives the nail into the wood and stops after the nail goes in a distance of 0.95 cm. The weight of the hammer head is 6N, and in addition to this weight there is a force of 14 N exerted on the hammer head by the person using the hammer. Assume that the acceleration of the hammerhead is constant while it is contact with the nail and moving downward, (i.e., while the hammer is slowing from its initial speed to zero). Calculate the magnitude of the downward force exerted by the hammer head on the nail while it is driving the nail into the wood. (Hint: By Newton’s third law, the force of the hammer head on the nail has equal magnitude to the force of the nail up on the hammer head. Ask yourself what are all the forces on the hammer head.)

Homework Equations



V2 = V02 + 2a(x-x0)


The Attempt at a Solution



Take up as positive, thus:

V0 = -1.2 m/s
V = 0
X0 = .0095 m
X = 0

0 = -1.22 +2(a)(-.0095)
a = 75.7895 m/s2

Now i get stuck. I set up the equation

ma = Fnormal - Fperson - Fgrav

I'm not too sure how to continue. Help!

Looks like you are almost there.

You have the nail pushing up with the net deceleration on the mass of the hammer head and the force of the arm and shoulder being present throughout the deceleration as well as gravity on the mass. So I would write it as

F = (75.79)*(6N)/(9.8) +14N + 6N
 
TL;DR Summary: I came across this question from a Sri Lankan A-level textbook. Question - An ice cube with a length of 10 cm is immersed in water at 0 °C. An observer observes the ice cube from the water, and it seems to be 7.75 cm long. If the refractive index of water is 4/3, find the height of the ice cube immersed in the water. I could not understand how the apparent height of the ice cube in the water depends on the height of the ice cube immersed in the water. Does anyone have an...
Kindly see the attached pdf. My attempt to solve it, is in it. I'm wondering if my solution is right. My idea is this: At any point of time, the ball may be assumed to be at an incline which is at an angle of θ(kindly see both the pics in the pdf file). The value of θ will continuously change and so will the value of friction. I'm not able to figure out, why my solution is wrong, if it is wrong .
Back
Top