A 1600 kg jet engine is fastened to the fuselage of a passenger jet

AI Thread Summary
The discussion revolves around calculating the force on bolts securing a 1600 kg jet engine to a passenger jet during different conditions. When the plane is stationary, each bolt supports a force of approximately 5226.67 N, calculated using F=ma with gravity's acceleration. During turbulence, the upward acceleration of 2.0 m/s² increases the force on each bolt to about 6293.33 N, as the gravitational force is combined with the upward acceleration. The reasoning clarifies that the upward acceleration effectively increases the perceived weight of the engine, similar to the sensation of increased weight in an upward-moving elevator. Understanding the relationship between gravitational force and acceleration is crucial for these calculations.
sb13
Messages
21
Reaction score
0

Homework Statement



A 1600 kg jet engine is fastened to the fuselage of a passenger jet by just three bolts (this is the usual practice). Assume that each bolt supports one-third of the load. (a) Calculate the force on each bolt as the plane waits in line for clearance to take off. (b) During flight, the plane encounters turbulence, which suddenly imparts an upward vertical acceleration of 2.0 m/s2 to the plane. Calculate the force on each bolt now.

Homework Equations



F= ma


The Attempt at a Solution



I got the correct solutions for both (a) and (b)

(a) F=ma= (1600 kg)(9.8 m/s^2) = 15680 N/3= 5226.67 N

(b) F=ma= (1600 kg)(9.8 m/s^2 + 2.0 m/s^2) = 18880 N/3 = 6293.33 N
But on (b), I don't understand why the acceleration of gravity was added to the upward vertical acceleration of 2.0 m/s^2, isn't gravity pulling the plane down, and the 2.0 m/s^2 pulling it up, shouldn't it be 9.8-2.0?
 
Physics news on Phys.org


Because the plane is accelerating upward, the engine 'weighs' more due to its acceleration upward. The force due to an acceleration is in the opposite direction of the acceleration.
 


Ok. So the gravitational force ends up creating a greater force and because the acceleration is going upward, it is causing more force as well? What is the acceleration was -2.0 m/s^2 and the plane was being pulled downward, what effect would that have on the engine's force?
 


Think about this, when an elevator is accelerating upwards you feel heavier. The elevator is pulling you upwards but you feel a stronger downward force. Similarly when the elevator is accelerating downwards you feel lighter.
 


If the plane is accelerating downward, then the force due to acceleration points upward. The gravitational force is the same. It's the force due to acceleration of the plane that causes the change in the load of the bolts.

Gravitational force exists and is the same whether the plane is moving or stopped. The acceleration of the plane either adds to it or subtracts from it.
 
Kindly see the attached pdf. My attempt to solve it, is in it. I'm wondering if my solution is right. My idea is this: At any point of time, the ball may be assumed to be at an incline which is at an angle of θ(kindly see both the pics in the pdf file). The value of θ will continuously change and so will the value of friction. I'm not able to figure out, why my solution is wrong, if it is wrong .
Thread 'Trying to understand the logic behind adding vectors with an angle between them'
My initial calculation was to subtract V1 from V2 to show that from the perspective of the second aircraft the first one is -300km/h. So i checked with ChatGPT and it said I cant just subtract them because I have an angle between them. So I dont understand the reasoning of it. Like why should a velocity be dependent on an angle? I was thinking about how it would look like if the planes where parallel to each other, and then how it look like if one is turning away and I dont see it. Since...
Thread 'Voltmeter readings for this circuit with switches'
TL;DR Summary: I would like to know the voltmeter readings on the two resistors separately in the picture in the following cases , When one of the keys is closed When both of them are opened (Knowing that the battery has negligible internal resistance) My thoughts for the first case , one of them must be 12 volt while the other is 0 The second case we'll I think both voltmeter readings should be 12 volt since they are both parallel to the battery and they involve the key within what the...
Back
Top