How to Calculate Torque for Drilling?

AI Thread Summary
To calculate the torque needed for drilling, key factors include the density of the material, the depth of the drilling, and the diameter of the drill bit. While the torque itself is independent of the material being drilled, the required torque does vary based on the material's properties and the size of the drill bit. For detailed calculations, resources like the Wikipedia page on torque provide valuable information. Understanding these elements is crucial for determining the appropriate torque for effective drilling. Accurate torque calculations ensure optimal drilling performance.
RookieLearnin
Messages
1
Reaction score
0
Hi!
Gonna keep it short.
Can someone give me an information how to calculate the needed torque/power of a drill?
My guess what would be important to calculate this is the density of the material that's being drilled, the depth of the drilling, and the diameter of the drill? Right? But i just can't find any information how to do this.

Thx for any help u can give me.
 
Engineering news on Phys.org
The torque of the drill is independent of the material it is drilling into. The "torque required" to drill something does depend on the material and the size of the drill bit.

The http://en.wikipedia.org/wiki/Torque" has good explanations of torque and the calculations you will need.
 
Last edited by a moderator:

Thread 'Bubble formation in 4 mm gap vessel'

How did you find PF?: Via Google search Hi, I have a vessel I 3D printed to investigate single bubble rise. The vessel has a 4 mm gap separated by acrylic panels. This is essentially my viewing chamber where I can record the bubble motion. The vessel is open to atmosphere. The bubble generation mechanism is composed of a syringe pump and glass capillary tube (Internal Diameter of 0.45 mm). I connect a 1/4” air line hose from the syringe to the capillary The bubble is formed at the tip...
View full post »

Thread 'HP Required to move a robot 10meters at 1.5m/sec'

I need some assistance with calculating hp requirements for moving a load. - The 4000lb load is resting on ball bearing rails so friction is effectively zero and will be covered by my added power contingencies. Load: 4000lbs Distance to travel: 10 meters. Time to Travel: 7.5 seconds Need to accelerate the load from a stop to a nominal speed then decelerate coming to a stop. My power delivery method will be a gearmotor driving a gear rack. - I suspect the pinion gear to be about 3-4in in...
View full post »
Thread 'Calculate minimum RPM to self-balance a CMG on two legs'

Thread 'Calculate minimum RPM to self-balance a CMG on two legs'

Here is a photo of a rough drawing of my apparatus that I have built many times and works. I would like to have a formula to give me the RPM necessary for the gyroscope to balance itself on the two legs (screws). I asked Claude to give me a formula and it gave me the following: Let me calculate the required RPM foreffective stabilization. I'll use the principles of gyroscopicprecession and the moment of inertia. First, let's calculate the keyparameters: 1. Moment of inertia of...
View full post »

Similar threads

How Do Multi-Head Drill Mechanisms Operate?
Replies
3
Views
1K
Torque for drill to shear through material
Replies
2
Views
3K
How to Measure Torque Required for motor to spin a rotating shaft?
Replies
3
Views
4K
Understanding torque -- impact guns and high torque drills
Replies
9
Views
3K
Calculation torque of a drive at the torque arm
Replies
5
Views
2K
How to calculate required torque for a robot arm
Replies
2
Views
4K
How much should I adjust torque when using anti-seize?
Replies
22
Views
5K
Calculate drive torque for rotating large drums
Replies
12
Views
3K
Torque calculations: Rotating vertical shaft
Replies
5
Views
5K
Specified Torque Specs on Automotive Fasteners -- Required or just suggestions?
Replies
13
Views
4K

Hot Threads

Recent Insights

Back
Top