Coefficient of Kinetic Friction

AI Thread Summary
The discussion revolves around a physics problem involving a 5.20 kg block moving up an inclined plane. The change in kinetic energy was calculated as -154.154 J, and the change in potential energy was found to be 75.6 J. The frictional force acting on the block was determined to be 26.18 N. The coefficient of kinetic friction was initially miscalculated as 3.327 due to a calculator error, but it was clarified that the correct value is approximately 0.59 after correcting for radians. The conversation highlights the importance of ensuring calculator settings are accurate when performing physics calculations.
yb1013
Messages
55
Reaction score
0

Homework Statement



A 5.20 kg block is set into motion up an inclined plane with an initial speed of v0 = 7.70 m/s. The block comes to rest after traveling 3.00 m along the plane, which is inclined at an angle of 30.0° to the horizontal.

(a) For this motion, determine the change in the block's kinetic energy.

I got -154.154 (correct)

(b) For this motion, determine the change in potential energy of the block-Earth system.

I got 75.6 (correct)

(c) Determine the frictional force exerted on the block (assumed to be constant).

I got 26.18 (correct)

(d) What is the coefficient of kinetic friction?

However, I could not figure this out for the life of me. Please help with the kinetic friction?

Homework Equations



I think the coeff. can be found with f=μmgCosθ , however my answer keeps coming out wrong...

The Attempt at a Solution



after using the previous formula, I came out with a value of μ=3.327 (26.18=u(5.2)(9.81)(cos(30))
 
Physics news on Phys.org
is the answer .59?
 
I don't understand how you get 3.327... coefficiant of friction isn't going to be more than 1

if you calculate what you have

(26.18=u(5.2)(9.81)(cos(30))

u get

26.18=44.13u

divide by 44.13
=.59
 
oooooo haha, thank you sir, my calculator somehow reverted itself back to radians?

Thanks again!
 
yb1013 said:
oooooo haha, thank you sir, my calculator somehow reverted itself back to radians?

Thanks again!

no prob. you did all the hard work haha
 
TL;DR Summary: I came across this question from a Sri Lankan A-level textbook. Question - An ice cube with a length of 10 cm is immersed in water at 0 °C. An observer observes the ice cube from the water, and it seems to be 7.75 cm long. If the refractive index of water is 4/3, find the height of the ice cube immersed in the water. I could not understand how the apparent height of the ice cube in the water depends on the height of the ice cube immersed in the water. Does anyone have an...
Thread 'Variable mass system : water sprayed into a moving container'
Starting with the mass considerations #m(t)# is mass of water #M_{c}# mass of container and #M(t)# mass of total system $$M(t) = M_{C} + m(t)$$ $$\Rightarrow \frac{dM(t)}{dt} = \frac{dm(t)}{dt}$$ $$P_i = Mv + u \, dm$$ $$P_f = (M + dm)(v + dv)$$ $$\Delta P = M \, dv + (v - u) \, dm$$ $$F = \frac{dP}{dt} = M \frac{dv}{dt} + (v - u) \frac{dm}{dt}$$ $$F = u \frac{dm}{dt} = \rho A u^2$$ from conservation of momentum , the cannon recoils with the same force which it applies. $$\quad \frac{dm}{dt}...
Back
Top