Design Project Help: Get Guidance for Your Final Year Project

  • Thread starter Thread starter JOSEPH W
  • Start date Start date
  • Tags Tags
    Design Project
AI Thread Summary
The discussion centers on a final year design project involving a system that applies plastic hanging tabs to products using motors and actuators. The project requires guidance on writing, calculations, and overall design. The user expresses uncertainty about where to start and seeks advice before consulting college resources. Despite the request for help, no responses have been provided in four years, indicating a lack of engagement on the topic. The original poster's situation highlights the challenges faced by students in seeking project guidance.
JOSEPH W
Messages
1
Reaction score
0
Hello folks I am about to start on my final year project and I am not sure how to go about it ,, as in what I need to write about and what calculations I should do relative to my design, its bascailly a system that apply s plastic hanging tabs to a product ,basically it will be a motor that will be connected to a acuator that will go up and down when the motor is turned which will apply the tabs ,, the tabs will aslo be on a reel turned by another motor and sensors to allow it to feed and when not to feed the next tab, anyone any info on projects and were would I start, I have to build and design it and I am kinda lost , I will ask for help in college but just looking for some guidness here first ,, thanks in advance :smile:
 
Engineering news on Phys.org
And no one has replied in FOUR YEARS! :)) Sorry dude wish I could have helped but you probably already finnished
 

Thread 'Race car suspension Class'

Posted June 2024 - 15 years after starting this class. I have learned a whole lot. To get to the short course on making your stock car, late model, hobby stock E-mod handle, look at the index below. Read all posts on Roll Center, Jacking effect and Why does car drive straight to the wall when I gas it? Also read You really have two race cars. This will cover 90% of problems you have. Simply put, the car pushes going in and is loose coming out. You do not have enuff downforce on the right...
View full post »
Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Scenario 1 (figure 1) A continuous loop of elastic material is stretched around two metal bars. The top bar is attached to a load cell that reads force. The lower bar can be moved downwards to stretch the elastic material. The lower bar is moved downwards until the two bars are 1190mm apart, stretching the elastic material. The bars are 5mm thick, so the total internal loop length is 1200mm (1190mm + 5mm + 5mm). At this level of stretch, the load cell reads 45N tensile force. Key numbers...
View full post »

Thread 'Cantilever help'

I'm trying to decide what size and type of galvanized steel I need for 2 cantilever extensions. The cantilever is 5 ft. The space between the two cantilever arms is a 17 ft Gap the center 7 ft of the 17 ft Gap we'll need to Bear approximately 17,000 lb spread evenly from the front of the cantilever to the back of the cantilever over 5 ft. I will put support beams across these cantilever arms to support the load evenly
View full post »

Similar threads

Help with designing a tool to hold a work piece (work piece jig)
Replies
9
Views
2K
Help needed with an Engineering project
Replies
23
Views
2K
Class Project: Tennis Ball Launcher
Replies
11
Views
7K
Need help on designing a conceptual HALE UAV
Replies
11
Views
2K
Help with my first ever design project?
Replies
14
Views
2K
Gear Wear Rig Design: Calculating Load for Maximum Durability
Replies
6
Views
2K
Creative Engineering Projects: Inspiring Ideas for Final Year Projects
Replies
2
Views
2K
Design a flywheel for my final year project
Replies
11
Views
4K
Final year raytracer project ideas
Replies
3
Views
2K
What are some good ideas for capstone project?
Replies
2
Views
2K

Hot Threads

Recent Insights

Back
Top