Exergy analysis gas turbine cycle For EEs

AI Thread Summary
The discussion focuses on the exergy analysis of a gas turbine cycle using EES software, specifically addressing the unexpected decrease in exergy efficiency of both the turbine and compressor with increasing inlet temperatures. The user seeks clarification on why turbine work increases with temperature but exergy efficiency decreases, and similarly, why compressor efficiency declines despite reduced work. They are also looking for articles to validate their findings and code, noting discrepancies between their results and established literature regarding the effects of ambient temperature on exergy efficiency and destruction. The user expresses a need for guidance to resolve these issues and validate their programming results.
amir star
Messages
5
Reaction score
0
hi friends,

I am working EES software for thermodynamic lesson,I am analyzing second law efficiency(exergy efficiency) and exergy analysis for all components of gas turbine cycle.

Now I have a problem,exergy efficiency of turbine decrease with increasing before temperature,why?

As you know, with increasing before temperature of turbine, increase work of turbine, so increase exergy efficiency of turbine.am I correct saying?

too, I have another problem,exergy efficiency of turbine decrease with increasing before temperature,why?

with increasing before temperature of compressor , decrease work of compressor , so decrease exergy efficiency of compressor .

have you articles that relate to obtain exergy of components gas turbine cycle?...I am searching but anything finding well, in fact I want to my code validate with articles.
another Question...

according to following article, exergy efficiency of Ideal air-standard simple cycle increase with increasing ambient temperature but For me(code that write) decrease.why?

and Exergy destroyed of cycle decrease with increasing ambient temperature but for me increase.why?

process of compressor and turbine consider constant entropy and Ideal air-standard simple cycle.

I think everything I observe.

http://0up.ir/up10/guest/1_7cf9a.rar

in fact, I am programing in EEs, Now I have some problem,

problem described in previous posts,

gas turbine cycle is as follows:



http://www.upload7.ir/imgs/2014-12/86515550666943192076.jpg

and equations:
compressor:

http://www.upload7.ir/imgs/2014-12/26181649452134491050.jpg

turbine:

http://www.upload7.ir/imgs/2014-12/69904976515215219246.jpg

< Questionable link deleted by Moderators >[/color]
 
Last edited by a moderator:
hi,

thanks for answer,

I want to valid conclusions in bellow Paper but not valid, thanks for your guide , wrote Cod in software EEs also attached,Do you working with software EEs?

attention to seventh page from paper , Four efficiency must be reduced but diagrams of out of EEs is not.

thanks

Paper:

http://0up.ir/up10/guest/6_ca7e4.pdfCODE:

http://0up.ir/up10/guest/sssss2_48e9d.rar
 
Last edited:
Posted June 2024 - 15 years after starting this class. I have learned a whole lot. To get to the short course on making your stock car, late model, hobby stock E-mod handle, look at the index below. Read all posts on Roll Center, Jacking effect and Why does car drive straight to the wall when I gas it? Also read You really have two race cars. This will cover 90% of problems you have. Simply put, the car pushes going in and is loose coming out. You do not have enuff downforce on the right...
I'm trying to decide what size and type of galvanized steel I need for 2 cantilever extensions. The cantilever is 5 ft. The space between the two cantilever arms is a 17 ft Gap the center 7 ft of the 17 ft Gap we'll need to Bear approximately 17,000 lb spread evenly from the front of the cantilever to the back of the cantilever over 5 ft. I will put support beams across these cantilever arms to support the load evenly
Thread 'What's the most likely cause for this carbon seal crack?'
We have a molded carbon graphite seal that is used in an inline axial piston, variable displacement hydraulic pump. One of our customers reported that, when using the “A” parts in the past, they only needed to replace them due to normal wear. However, after switching to our parts, the replacement cycle seems to be much shorter due to “broken” or “cracked” failures. This issue was identified after hydraulic fluid leakage was observed. According to their records, the same problem has occurred...
Back
Top