What is the best way to determine the mass percentage of NaOH in Plumbo?

  • Thread starter Thread starter Thallium
  • Start date Start date
  • Tags Tags
    Major School
AI Thread Summary
The discussion revolves around determining the mass percentage of NaOH in Plumbo through titration. Initially, there was uncertainty about the appropriateness of titration as a method, but it was confirmed to be a suitable approach. Participants emphasized the importance of using an indicator, such as phenolphthalein or bromothymol blue (BTB), for accurate pH measurement during the titration process. The procedure involved titrating a known volume of Plumbo with hydrochloric acid (HCl) to reach pH 7, allowing for the calculation of moles of NaOH present. The calculations used the formula n=m/Mm to derive the mass percentage of NaOH based on the titration results. Despite initial doubts and challenges, including misleading advice from a teacher, the group successfully completed the experiment and confirmed the method's simplicity.
Thallium
Messages
231
Reaction score
0
I am preparing an experiment to find out what the mass percentage of NaOH in Plumbo is and someone has allready suggested using titration, but that did not seem logic. I know how to calculate the mass percentage, but I and my group were given a sheet of paper with a problem which we are to solve. We are to make an suggestion for how to solve this problem, and I am in doubt whether this is very simple or very complicated.

PLEASE HELP!
 
Chemistry news on Phys.org
Can you state the problem exactly as it appears on your sheet of paper.
 
Titrate. Simple.

I'm guessing Plumbo is a liquid?

Do you have access to phenolphtalein or a similar indicator? Otherwise you will have to check every while with pH paper...Maybe you have a digital meter, that would be good..

Anyway, it's not hard...Just take x volume (mass it) of plumbo...titrate to pH 7 with known molarity of acid...figure out how many moles of acid were needed to bring to pH 7, and that's how many moles of base are present in x volume of plumbo. Convert these moles to grams, then take this number, divide it by the mass of the volume of plumbo you used = mass %.
 
We have found out now and I hope we have done well.

The problem was as follows: Find the mass percentage of NaOh in PLUMBO. Nothing more, nothing less. We needed to plan what tools we were to use, what calculations we were to take and what chemicals we were to use.

We titrated with HCl three times and evaluated the results and the observations. the calculation method we used was n=m/Mm and then found the mass percentage. It wasn't harder than that though we had been working on it for hours and even our teacher gave us inaccurate or more or less incorrect advices.

The indicator was BTB!
 

Thread 'Humidity of a saturated NaCl solution with anticaking additive'

I want to test a humidity sensor with one or more saturated salt solutions. The table salt that I have on hand contains one of two anticaking agents, calcium silicate or sodium aluminosilicate. Will the presence of either of these additives (or iodine for that matter) significantly affect the equilibrium humidity? I searched and all the how-to-do-it guides did not address this question. One research paper I found reported that at 1.5% w/w calcium silicate increased the deliquescent point by...
View full post »

Similar threads

Testing Passing the Cisco 200-125 CCNA exam with good percentage
Replies
2
Views
1K
Determine the amount of NaOH and Sr(OH)2 based on pOH
Replies
3
Views
3K
What additional courses should I take as a chem major?
Replies
5
Views
2K
Percentage yield in a reaction problem
Replies
4
Views
3K
What is the percentage of Fool's Gold in the original sample?
Replies
10
Views
2K
Determine amount of base to use for titration?
Replies
1
Views
3K
What's the best major between Physics & Chemistry for entering MS in Nuclear Engineering?
Replies
12
Views
2K
I Solving a momentum problem where masses change after the collision
Replies
35
Views
3K
Classical What are the best intermediate Newtonian mechanics textbooks?
Replies
23
Views
5K
Admissions Advice on how best to spend my time for graduate school applications
Replies
15
Views
2K

Hot Threads

Recent Insights

Back
Top