Finding the angle of the traveling direction of a sailboat

  • Thread starter Thread starter TmrK
  • Start date Start date
  • Tags Tags
    Angle Direction
AI Thread Summary
The discussion revolves around calculating the angle between the force exerted by the wind on a sailboat and due north. The problem states that the work done by two forces, F1 and F2, is equal despite their different directions and distances. The participant uses trigonometric relationships to express the work done as W = F1(cosθ)d and equates the work done by both forces. They derive that cosθ = 0.76, leading to an angle of approximately 40.54° west of north. The solution emphasizes the importance of checking calculations by substituting values back into the original equations to verify correctness.
TmrK
Messages
21
Reaction score
0

Homework Statement


As a sailboat sails 55 m due north, a breeze exerts a constant force F1 on the boat's sails. This force is directed at an angle west of due north. A force F2 of the same magnitude directed due north would do the same amount of work on the sailboat over a distance of just 42 m. What is the angle between the direction of F1 and due north?


Homework Equations


Don't know if this pertains to adding the forces together.


The Attempt at a Solution


I assume that trigonometry is involved here to solve this problem. Other than that, that's how far I have gotten into the problem.
 
Physics news on Phys.org
Well W=Fd, where the force F is in the same direction as the distance d.

You know that F1=F2 from the problem.
And W1=W2

And, from the second case the work W2=F2 x 42m

But as the sailboat is traveling due north, and a breeze is acting on the sails with a force F1 at a certain angle, west of due north. Here, the work W1 on the sailboat would be the component of F1 in the north direction and the distance 55m.
 
256bits said:
Well W=Fd, where the force F is in the same direction as the distance d.

You know that F1=F2 from the problem.
And W1=W2

And, from the second case the work W2=F2 x 42m

But as the sailboat is traveling due north, and a breeze is acting on the sails with a force F1 at a certain angle, west of due north. Here, the work W1 on the sailboat would be the component of F1 in the north direction and the distance 55m.

So with this, W=F1(cosθ)d

And plugging in the equations,
F1(cos\Theta)55m = F2 X 42m (being that cos0°=1)

divide F on both sides,
cosθ55m = 42m

divide 55m with 42m, and I assume that in the end,
cosθ = .7(63 repeating)°
cosθ = .76°

Am I close?
 
divide 55m with 42m, and I assume that in the end,
cosθ = .7(63 repeating)°
cosθ = .76°

Am I close?

0.76° --> the little dot goes on the angle but not on the cos of the angle. Sine, cosine, tangent come from the ratios of the sides of a traingle and so dimensionless.

Close,
What angle θ will give cosθ=0.76.
They ask for the angle, and, I presume, you have to state whether or not it is east of north or west of north angle.
If you draw a diagram of the sailboat and forces you should be able to figure that out visually.

Hint;
to check if your answer is correct or not, put the values back into the equation.
ie W2 = F2 x 42

W1 = F1 cosθ x 55 = F1 0.76 x 55 = F1 x 42

Since F1 = F2, then W1 = W2 and correct.

You could do that for all problems you encounter as a check.
 
I get the impression that the author of this problem doesn't understand how sailboats work.
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top