Finding vertical velocity at highest point in trajectory

AI Thread Summary
The discussion centers on calculating the vertical and horizontal components of a polo ball's release velocity after being hit at a 33-degree angle with a release velocity of 30 m/s. The vertical component is calculated as 16.34 m/s, and there is confusion about whether this value should be negative when considering the ball's descent. At the highest point of the trajectory, the vertical velocity is zero, which raises questions about using the release velocity for calculations. The conversation emphasizes understanding the conditions that define the highest point in the trajectory, where the projectile momentarily stops ascending before descending. Clarification is sought on the correct approach to calculating velocities at different points in the ball's flight.
honey.s
Messages
3
Reaction score
0
Hey ya'll ... I just need clarification on this solution. Is it correct in me saying the vertical component is negative as the ball is falling to the ground? Also, I was unsure whether to use the vertical velocity or release velocity in finding the highest point of trajectory

Q: A polo ball is hit from the ground at an angle of 33 degrees upwards from the horizontal. If it has a release velocity of 30 m/s and lands on the ground, calculate the vertical and horizontal components of its release velocity and provide these answers in the answer boxes provided.

(i) What are the vertical and horizontal components?

sin33= x/30

vertical component = 16.34 (should this be negative because the ball is falling down??)

cos33= y/30

Horizontal component = 25.16

(ii)What will be the vertical velocity of the ball be at the highest point in its trajectory.

s=Final velocity - initial velocity / 2a

s= 0-(16.34)^2 / 2(9.8)

=13.6 (is it correct in me using the vertical velocity as opposed to release velocity?)

Thankyou in advance
 
Physics news on Phys.org
If the ball at its highest point has a positive velocity, then what prevents it from being a little higher than the "highest" a little bit later?
 
If I use the release velocity, then s= 0- (30)^2 / 2 (9.8), and therefore the answer is 45.9 and at its highest. That was my initial thought, but the next question asks for the horizontal velocity of the ball at its highest point, and that's why I thought we had to use vertical and horizontal velocity respectively..
 
You got an even higher value for vertical velocity at the apex. My argument in #2 applies.

You should think about what condition defines the highest point of the trajectory. Where is the projectile going just before the highest point, and where is it going after?
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top