How can I safely power a laptop from my car battery without burning it out?

  • Thread starter Thread starter Miller44
  • Start date Start date
  • Tags Tags
    Car pc
AI Thread Summary
Powering a laptop directly from a car battery is feasible since the laptop will only draw the current it needs at its specified voltage of 12.65 volts. However, car electrical systems can spike to around 14 volts, which may risk overheating or damaging the laptop. To ensure safety, using a dedicated car power adapter that regulates voltage and current is recommended. These adapters can buffer electrical noise and provide the necessary voltage adjustments for the laptop. Overall, using a commercial power adapter designed for automotive use is the safest approach to avoid potential damage.
Miller44
Messages
2
Reaction score
0
Hello,

I am installing a small laptop computer in the dash of my car. My question is:

If the power supply from the battery of the laptop (which I do not have) is 12.65 volts at 2200 mA and I want to power it from the car battery (12.65 volts). Will the laptop only draw 2200 mA or will it burn out? And how would i lower the amperage if I need too? I have built minor circuits and have some knowledge on circuitry but I am just a little confused by this. Any advice would be appreciated!
 
Engineering news on Phys.org
Miller44 said:
Hello,

I am installing a small laptop computer in the dash of my car. My question is:
This is a driving hazard.
 
Ignoring the hazards I plunge ahead...

Your device will only draw the amount of current it "needs" at it's specified supply voltage. However automobile electrical systems can go up to around 14 volts when being charged, so your computer might feel like drawing more current than it should. It's probable that the guts of the computer are well enough designed that this won't be an issue, but they might be close enough to their design limits that an extra volt or two could push them over to the dark side. Pretty much the only way to know is to try it and see if anything heats up too much.
 
Awesome, that was my initial thought but I had to check. I bought a lot of 5 so if one goes ill be fine. And for saftey measures ill wire it to the parking break ;]. Thanks again!
 
I'd recommend going with something like this, instead:
http://www.targus.com/us/product_details.aspx?sku=APD80US
http://www.targus.com/us/product_details.aspx?sku=APM69US
http://us.kensington.com/html/17588.html

As schip666! says, car electricity isn't always very clean. These are designed to just plug into the cigarette lighter, buffer out any spikes or garbage, and step up/down the voltage to whatever the laptop needs (I think the second Targus and the Kensington also allow you to plug them into the wall as well, if you happen to want that functionality).

I used one a previous model of the first Targus, which worked quite well--just plug in the model of your laptop on their page and it'll tell you which tip is required (and whether it's supplied with the unit, or whether you need to get them to send you a free one). I think both these companies (and others, including RAM mounts) supply in-car laptop mounting solutions as well, assuming you don't want to build your own, or just leave it on the dash.
 
Last edited by a moderator:
While I was rolling out a shielded cable, a though came to my mind - what happens to the current flow in the cable if there came a short between the wire and the shield in both ends of the cable? For simplicity, lets assume a 1-wire copper wire wrapped in an aluminum shield. The wire and the shield has the same cross section area. There are insulating material between them, and in both ends there is a short between them. My first thought, the total resistance of the cable would be reduced...
Hey guys. I have a question related to electricity and alternating current. Say an alien fictional society developed electricity, and settled on a standard like 73V AC current at 46 Hz. How would appliances be designed, and what impact would the lower frequency and voltage have on transformers, wiring, TVs, computers, LEDs, motors, and heating, assuming the laws of physics and technology are the same as on Earth?
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
Back
Top