How can I solve a Thevenin problem involving two batteries?

AI Thread Summary
To solve a Thevenin problem involving two batteries, start by converting the voltage sources into current sources using source conversion. Calculate the effective resistances for each side after converting, resulting in values of 2.545 ohms for the left and 2.25 ohms for the right. Convert these back to voltage sources to find the Thevenin voltage, which is 1.635 V. The total resistance in the circuit is 14.545 ohms, leading to a current of approximately 0.1124 A. Using Thevenin's theorem, remember to treat the voltage source as a short circuit to simplify calculations.
vbs
Messages
1
Reaction score
0

Homework Statement



Hi there, I got this question from an old test. I would say I have limited knowledge of electronics and would ask for guidance into what approach to take with this question.

Homework Equations





The Attempt at a Solution



No attempt yet. I thought of breaking it up, in 2, obviously, and then getting the series resistance total, but what then? then I am back at square 1, with a "broken" circuit. What small detail am I missing?
 

Attachments

  • IND_ELEC_FIG1.jpg
    IND_ELEC_FIG1.jpg
    22.2 KB · Views: 680
Physics news on Phys.org
1) Change the voltage source into a current source using source conversion.
i.e current source with current = 12V / 4ohm= 3 A. - lookin at the left voltage source.
you will get 3A current source with a resistor of 4 ohm connecting parallel to it.

do for the other side(right) too. 8/3=2.67A

2) Since you then have resistors in parallel.
the effective resistance on the left will then be (4*7)/ (4+7)= 2.545 ohm
right will be 2.25 ohm.

3) Convert them back to voltage source.
LEft: 2.545 *3 = 7.635 V
Right : 2.25 * 2.67= 6V

The resultant voltage will be 7.635 - 6 = 1.635 V.
Sum of all the resistance = 10 + 2.545 + 2=14.545 ohm
Hence without using thevenin,
I = 1.635 / 14.545 = 0.1124A

Using thevenin,

After using source conversion,
Golden rule: Make current source disappear; make voltage source a short circuit, meaning: treat it just as a piece of connecting wire.

thevenin voltage = thevenin resistance * short circuit current.
then calculate the current you wanted by current divider rule.

hope this helps
 
1) Change the voltage source into a current source using source conversion.
i.e current source with current = 12V / 4ohm= 3 A. - lookin at the left voltage source.
you will get 3A current source with a resistor of 4 ohm connecting parallel to it.

do for the other side(right) too. 8/3=2.67A

2) Since you then have resistors in parallel.
the effective resistance on the left will then be (4*7)/ (4+7)= 2.545 ohm
right will be 2.25 ohm.

3) Convert them back to voltage source.
LEft: 2.545 *3 = 7.635 V
Right : 2.25 * 2.67= 6V

The resultant voltage will be 7.635 - 6 = 1.635 V.
Sum of all the resistance = 10 + 2.545 + 2=14.545 ohm
Hence without using thevenin,
I = 1.635 / 14.545 = 0.1124A

Using thevenin,

After using source conversion,
Golden rule: Make current source disappear; make voltage source a short circuit, meaning: treat it just as a piece of connecting wire.

thevenin voltage = thevenin resistance * short circuit current.
then calculate the current you wanted by current divider rule.

hope this helps
 
Thread 'Have I solved this structural engineering equation correctly?'
Hi all, I have a structural engineering book from 1979. I am trying to follow it as best as I can. I have come to a formula that calculates the rotations in radians at the rigid joint that requires an iterative procedure. This equation comes in the form of: $$ x_i = \frac {Q_ih_i + Q_{i+1}h_{i+1}}{4K} + \frac {C}{K}x_{i-1} + \frac {C}{K}x_{i+1} $$ Where: ## Q ## is the horizontal storey shear ## h ## is the storey height ## K = (6G_i + C_i + C_{i+1}) ## ## G = \frac {I_g}{h} ## ## C...

Similar threads

Back
Top