How Is Tension Distributed in a Multi-Block System?

  • Thread starter Thread starter physicsgrade11
  • Start date Start date
  • Tags Tags
    Confused Tension
AI Thread Summary
In a multi-block system where a girl pulls three blocks with a force of 6 N, the tension in the rope between the first and second blocks is calculated to be 5 N, while the tension between the second and third blocks is 2 N. The weights of the blocks were initially misstated as Newtons but are actually in kilograms. The discussion emphasizes the importance of understanding the relationship between force and mass in calculating tension. Participants express a willingness to share the steps for solving the problem if needed. Overall, the conversation revolves around clarifying the tension distribution in the system.
physicsgrade11
Messages
9
Reaction score
0
Ok - I was helping a friend out and was helping her with a problem but I am not sure if i was right.
A girl is pulling three blocks with a rope at a force of 6 N . There is two more strings between each block. The first block weighs 0.5 N the second block weighs 1.5N the third block weighs 1 N. Ignore friction. What is the amount of tension on each rope? :confused:
 
Physics news on Phys.org
Sorry i made a mistake the weight of the blocks are meant to be in kilograms not N .
lol idiot me...
 
The force on the rope between the first and second blocks is 5N
And the force on the rope between the second and third blocks is 2N.

I hope that helps
If you need the steps to get the answers, just ask.
 
physicsgrade11 said:
Sorry i made a mistake the weight of the blocks are meant to be in kilograms not N .
lol idiot me...
The unit of weight IS Newton, though..
 
Miracles said:
The force on the rope between the first and second blocks is 5N
And the force on the rope between the second and third blocks is 2N.

I hope that helps
If you need the steps to get the answers, just ask.

hey... how'd u do it?

thanks much
 
Thread 'Voltmeter readings for this circuit with switches'

Thread 'Voltmeter readings for this circuit with switches'

TL;DR Summary: I would like to know the voltmeter readings on the two resistors separately in the picture in the following cases , When one of the keys is closed When both of them are opened (Knowing that the battery has negligible internal resistance) My thoughts for the first case , one of them must be 12 volt while the other is 0 The second case we'll I think both voltmeter readings should be 12 volt since they are both parallel to the battery and they involve the key within what the...
View full post »
Thread 'Correct statement about a reservoir with an outlet pipe'

Thread 'Correct statement about a reservoir with an outlet pipe'

The answer to this question is statements (ii) and (iv) are correct. (i) This is FALSE because the speed of water in the tap is greater than speed at the water surface (ii) I don't even understand this statement. What does the "seal" part have to do with water flowing out? Won't the water still flow out through the tap until the tank is empty whether the reservoir is sealed or not? (iii) In my opinion, this statement would be correct. Increasing the gravitational potential energy of the...
View full post »

Similar threads

Force pulling on a string at an angle with a block at the other end
Replies
2
Views
1K
Why Does Calculating Tension in Multiple Blocks Require Different Forces?
Replies
2
Views
1K
Static Friction Required to Keep the System from Moving (Two Boxes)
Replies
16
Views
3K
Newton's law problem: Pushing 2 stacked blocks on a horizontal table
Replies
13
Views
3K
What is the maximum tension and friction force for a block held on an incline?
Replies
19
Views
4K
Tension in the wire connecting two blocks
Replies
5
Views
2K
Why is the tension force equal to friction force
Replies
9
Views
7K
Tension force of block and rope
Replies
25
Views
5K
What is the relationship between tension and mass in a system with friction?
Replies
6
Views
2K
The tension in the cord in this system
Replies
7
Views
2K

Hot Threads

Recent Insights

Back
Top